BEKO WML 65100 User Manual

EN19
C	 More	laundry	may	be	loaded	during	the time delay period.
5. At the end of countdown process, 
“:”	will	light	up	continuously,	“Ready”	
light will go off and the relevant program 
follow-up light will come on according to 
the selected program.
Changing the delay time
If you want to change the time during 
the	countdown:
1.	Press	“Start/Pause/Cancel”	button.	
“:”	in	the	middle	of	the	screen	will	stop	
flashing.
2.	Pres	“Time	Delay”	button	to	adjust	
the desired time delay.
3.	Press...

EN20
change can be made in the running 
program.
The machine is switched to child-lock 
by pressing the 2nd and 3rd auxiliary 
functions	for	3	sec.	“C	on”	(Child	lock	is	
activated)	label	appears	on	the	screen.	
The same symbol will also be displayed 
whenever any button is pressed while 
the machine is child-locked.
Child-proof lock lamp on the program 
follow-up indicator will light up when the 
child-proof lock is activated.
To deactivate the child-proof lock, 
press the 2nd and 3rd auxiliary function...

EN21
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3.  Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2.  Select the programme and the 
temperature.
3.	 If	required:
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4.  Close the loading door.
5.	 Press	“Start/Pause/Cancel”	 button. The display shows the 
time remaining for the program to 
complete if time delay is not set....

EN22
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C  If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2.  Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate...

EN23
Draining any remaining water 
and cleaning the pump filter
Filter system in your machine prevents 
solid items such as buttons, coins and 
fabric fibers clogging the pump propeller 
during discharging of the washing 
water. Thus, a good water discharger is 
achieved and the pump life is extended.
•		 If	your	machine	fails	to	drain	the	water, the pump filter may be 
clogged.	You	may	have	to	clean	
it every 2 years or whenever it is 
blocked plugged. Water must be 
drained off to clean the pump...

EN24
hose and fit the hose back into its 
place.
If your product is not supplied with an 
emergency drain hose, do the following 
as	shown	in	the	figure	below:
•		 Place	a	large	container	in	front	of	the	 filter to receive water flowing from 
the filter.
•		 Loosen	pump	filter	(anticlockwise)	 until water starts to flow out of it. 
Direct the flowing water into the 
container you have placed in front 
of	the	filter.	You	can	use	a	piece	of	
cloth to absorb any spilled water.
•		 When	there	is	no	water...

EN25
ProblemCause Explanation / Suggestion
Program	
cannot be 
started or 
selected. Machine	may	have	
switched to self 
protection mode due to 
an infrastructure problem 
(such	as	line	voltage,	
water	pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/
Cancel”	button	for	3	seconds.	(see,	Cancelling	
a	Program)
Water in the 
machine. There may be some water 
in your machine when you 
receive it. This is from the 
quality control process 
and is normal.
It is not harmful to your machine.
There...

EN26
The water 
being taken 
in is directly 
discharged.Improper position of the 
drain hose.
Connect the water draining hose as described 
in the operation manual.
No water can 
be seen in 
the machine 
during 
washing. This is not a problem. The 
water level is not visible 
from the outside of the 
machine.
The door is 
jammed. Water level might be 
above the lower level of 
the door.
Run	either	the	“Pump”	or	“Spin”	program.
Machine	might	be	heating	
up the water or it may be 
at the spinning cycle....

EN27
It continuously 
washes.
Remaining 
time does not 
count down.In the case of a paused 
countdown while taking in 
water:
Timer will not countdown 
until the machine is filled 
with the correct amount 
of water.
The machine will wait until there is a sufficient 
amount of water to avoid poor washing results 
due to lack of water. Then the timer will start to 
count down.
In the case of a paused 
countdown at the heating 
step:
Time will not count 
down until the selected 
temperature for the 
program...

EN28
Washing 
performance is 
poor:
Laundry turns 
gray - Using insufficient 
amount of detergent for a 
long time,
 - Washing at low 
temperatures for a long 
time,
 - Using insufficient 
amount of detergent for 
hard	waters	(soil	can	stick	
to	the	laundry),
 - Using excessive amount 
of	detergent	(detergent	
can	stick	to	the	laundry).  - Use the recommended amount of detergent 
appropriate for water hardness and the laundry.
 - Select the proper temperature for the laundry 
to be washed.
 - If the...