Beko Wml 15105 P Manual

EN21
Preparation
1. 
Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3.  Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2.  Select the programme and the 
temperature.
3.	 If	required	(according	to	your	 machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4.	 Close	the	loading	door.
5.	 Press	Start/Pause/Cancel	button.
Canceling a program
•	 Press	“Start/Pause/Cancel”	button...

EN22
3. 
Set the spin speed if spin speed 
adjustment is available on your 
machine.
4.	 Press	“Start/Pause/Cancel”	button.	
After the program is finished
1.	 “Program	finished”	lamp	will	light	 up on the program follow-up 
indicator. The lid can be opened 
after	2	minutes	when	the	“Program	
Finished”	and	“Lid”	lamps	light	up	
continuously.  
2.	 Press	the	On/Off	button	to	shut	 down the machine.
3.  Turn the water tap off.
4.	 Eliminate	any	folding	of	the	rubber	 seal on the loading door and check 
for...

EN23
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2.  Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate...

EN24
•	 If	the	filters	are	very	dirty,	you	can	
pull them out by means of pliers and 
clean them.
•	 Take	out	the	filters	on	the	flat	 ends of the water intake hoses 
together with the gaskets and clean 
thoroughly under streaming water.
•	 Replace	the	gaskets	and	filters	 carefully and tighten the hose nuts 
by hand.
Draining any remaining water 
and cleaning the pump filter
Filter system in your machine prevents 
solid items such as buttons, coins and 
fabric fibers clogging the pump propeller 
during...

EN25
replace the plug, pour the water out, 
then resume the draining process.
•	 After	draining	process	is	completed,	 replace the plug into the end of the 
hose and fit the hose back into its 
place.
If your product is not supplied with an 
emergency drain hose, do the following 
as	shown	in	the	figure	below:
•	 Place	a	large	container	in	front	of	the	 filter to receive water flowing from 
the filter.
•	 Loosen	pump	filter	(anticlockwise)	 until water starts to flow out of it. 
Direct the flowing water...

EN26
CauseExplanation / Suggestion
Programme	cannot	be	started	or	selected.
Machine	may	have	switched	to	
self protection mode due to an 
infrastructure	problem	(such	as	line	
voltage,	water	pressure,	etc.). Bring your machine to factory settings by turning 
the	programme	selection	knob.	(see,	Ending	the	
programme	through	Cancelling)
Water in the machine.
There may be some water in your 
machine when you receive it. This is 
from the quality control process and is 
normal. It is not harmful to your...

EN27
The door is jammed.
- Water level might be above the lower 
level of the door.
-	Machine	might	be	heating	up	the	
water or it may be at the spinning 
cycle.
- Due to an electrical mechanism, 
the door can only be opened a few 
minutes after the programme has 
stopped.-	Run	either	the	“Pump”	or	“Spin”	programme.
- Wait until the process is over.
- Wait until the process is over.
Machine	fills	with	water	when	a	process	is	cancelled.
Inside of machine may be hot. For safety reasons, water should be...

EN28
It continuously washes. Remaining time does not count down.
In the case of a paused countdown 
while	taking	in	water:
- Timer will not countdown until the 
machine is filled with the correct 
amount	of	water.	(On	models	with	
display)
- Time might have gotten stuck during 
heating	step.	(On	models	with	display)
In the case of a paused countdown at 
the	spinning	step:
There may be an imbalance of laundry 
in	the	machine.	(On	models	with	
display)- The machine will wait until there is sufficient...

EN29
-	Washing	performance	is	poor:	Oily	stains	appear	on	laundry.	
-	Washing	performance	is	poor:	Bad	odour
-	Oily	accumulations	on	the	drum	may	
have stuck to the laundry.
-	Oily	accumulations	on	the	drum	may	
have stuck to the laundry.- Such odours and bacteria layers are formed on 
the drum as a result of continuous washing at 
lower temperatures and/or in short programmes.
- Leave the detergent dispenser drawer as well 
as the loading door of the machine ajar after each 
washing. Thus, a humid...

EN30
Clothes do not smell like the softener.
- Insufficient amount of detergent used.
- The detergent was placed into the 
wrong	compartment;	the	detergent	
was mixed with the softener.- If the water hardness is higher, using insufficient 
amount of detergent can cause the laundry to 
become stiff in time. Use appropriate amount of 
detergent according to the water hardness.
- If detergent is put in the prewash compartment 
although prewash cycle is not selected, machine 
can take this detergent during...