BEKO WMD 75106 User Manual

Washing Machine 
Перална машина 
Perilica rublja 
Plně automatická pračka
WMD 75106
 

2 - EN
1 Warnings
General Safety•	 Never	place	your	machine	on	a	carpet	covered	floor.	Otherwise,	lack	of	airflow	from	below	of	your	machine	may	cause	electrical	parts	to	overheat.	This	may	cause	problems	with	your	washing	machine.•	 If	the	power	cable	or	mains	plug	is	damaged	you	must	call	Authorized	Service	for	repair.•	 Fit	the	drain	hose	into	the	discharge	housing	securely	to	prevent	any	water	leakage	and	to	allow	machine	to	take	in	and	discharge	water	as	required.	It	is	very	important	that	the	water...

3 - EN
2 Installation
Removing packaging 
reinforcementTilt	the	machine	to	remove	the	packaging	reinforcement.	Remove	the	packaging	reinforcement	by	pulling	the	ribbon.
Opening the transportation locksA	Transportation	safety	bolts	must	be	removed	before	operating	the	washing	machine!	Otherwise,	the	machine	will	be	damaged!1.	 Loosen	all	the	bolts	with	a	spanner	until	they	rotate	freely	(“C”)2.	 Remove	transportation	safety	bolts	by	turning	them	gently.3.	 Fit	the	covers	(supplied	in	the	bag	with	the...

4 - EN
Electrical connectionConnect	the	machine	to	an	earthed	outlet	protected	by	a	fuse	of	suitable	capacity.
Important:•		 Connection	should	comply	with	national	regulations.•		 The	voltage	and	the	allowed	fuse	protection	are	specified	in	the	section	“Technical	Specifications”.•		 The	specified	voltage	must	be	equal	to	your	mains	voltage.•		 Connection	via	extension	cords	or	multi-plugs	should	not	be	made.B	A	damaged	power	cable	must	be	replaced	by	a	qualified	electrician.B	The	appliance	must	not	be...

5 - EN
Display symbols
4  Selecting a Program and Operating Your Machine
1	 -	 Spin	Speed	Adjustment	Button
2	 -	 Time	Delaying	Button	(+/-)
3	 -	 Temperature	Adjustment	Button
4	 -	 Start/Pause/Cancel	Button
Control panelFigure 1
Figure 27.a	 -	 Spin	Speed	Indicator
7.b	 -	 Temperature	Indicator
7.c	 -	 Spin	Symbol
7.d	 -	 Temperature	Symbol
7.e	 -	 Remaining	Time	and	Delaying	Time	Indicator
7.f	 -	 Programme	Indicator	Symbols	(pre-wash/main	wash/rinse/softener/spin)
7.g	 -	 Economy	Symbol
7.h	 -	 Time...

6 - EN
Main programs Depending	on	the	type	of	textile,	the	following	main	programs	are	available:
• CottonsYou	can	wash	your	durable	clothes	with	this	program.	Your	laundry	will	be	washed	with	vigorous	washing	movements	during	a	longer	washing	cycle.
• SyntheticsYou	can	wash	your	less	durable	clothes	on	this	program.	Lighter	washing	movements	and	shorter	washing	cycle	is	used	compared	to	“Cottons”	program.	It	is	recommended	for	your	synthetic	clothes	(such	as	shirts,	blouses,	synthetic/cotton	blended...

7 - EN
clothes	become	wrinkled	in	an	anhydrous	condition.	With	this	function,	your	laundry	is	kept	in	the	final	rinsing	water.	If	you	want	to	spin	your	laundry	after	the	rinse	hold	function:
-		 Adjust	the	spin	speed.-		 Press	“Start/Pause/Cancel”	button.	
Program	resumes.	Your	machine	drains	the	water	and	spins	your	laundry.	You	can	use	no	spin	function	in	order	to	drain	the	water	without	spinning	at	the	end	of	the	program.
•		Selectable
*		Automatically	selected,	not	cancelable.
**	Energy	Label	program...

8 - EN
Auxiliary functionsAuxiliary Function Selection ButtonsC	Select	the	required	auxiliary	functions	before	starting	the	program.C	Some	combinations	cannot	be	selected	together.	(Ex.:	Pre-wash)	(Figure	1-5a)	and	Quick	Wash	(Figure	1-5b).
Auxiliary function selectionIf	an	auxiliary	function	that	should	not	be	selected	together	with	a	previously	selected	function	is	chosen,	the	first	selected	function	will	be	cancelled	and	the	last	auxiliary	function	selection	will	remain	active.
(Ex.:	If	you	want	to...

9 - EN
brought	to	the	appropriate	position,	rpm	and	temperature	data	reappear.
Switching the machine to standby 
modePress	“Start/Pause/Cancel”	button	momentarily	to	switch	your	machine	to	the	standby	mode.	Auxiliary	functions	can	be	cancelled	or	selected	in	accordance	with	the	step	the	program	is	at.	The	door	can	be	opened	if	the	water	level	is	suitable.	Laundry	may	be	added	/	taken	out	by	opening	the	door.
Door lockThe	Door	Locked	Symbol	(Figure	2-7i)	lights	up	when	the	loading	door	is	locked.	This...

10 - EN
by	pulling	out	the	plug	at	the	end	of	the	hose.	If	the	amount	of	water	to	be	drained	off	is	greater	than	the	volume	of	the	container,	replace	the	plug,	pour	the	water	out,	then	resume	the	draining	process.•		 After	draining	process	is	completed,	replace	the	plug	into	the	end	of	the	hose	and	fit	the	hose	back	into	its	place.If	your	product	is	not	supplied	with	an	emergency	drain	hose,	do	the	following	as	shown	in	the	figure	below:
•		 Place	a	large	container	in	front	of	the	filter	to	receive	water...