BEKO WMB 60831 User Manual

Washing Machine 
Перална машина 
Perilica rublja 
Plně automatická pračka
WMB 61031
WMB 61231
WMB 60831
WMB 61431
WMB 61231 S
WMB 61231 PT
 

2 - EN
1 Warnings
General Safety•	 Never	place	your	machine	on	a	carpet	covered	floor.	Otherwise,	lack	of	airflow	from	below	of	your	machine	may	cause	electrical	parts	to	overheat.	This	may	cause	problems	with	your	washing	machine.•	 If	the	power	cable	or	mains	plug	is	damaged	you	must	call	Authorized	Service	for	repair.•	 Fit	the	drain	hose	into	the	discharge	housing	securely	to	prevent	any	water	leakage	and	to	allow	machine	to	take	in	and	discharge	water	as	required.	It	is	very	important	that	the	water...

3 - EN
2 Installation
Removing packaging reinforcementTilt	the	machine	to	remove	the	packaging	reinforcement.	Remove	the	packaging	reinforcement	by	pulling	the	ribbon.
Opening the transportation locks
A	Transportation	safety	bolts	must	be	removed	before	operating	the	washing	machine!	Otherwise,	the	machine	will	be	damaged!1.	 Loosen	all	the	bolts	with	a	spanner	until	they	rotate	freely	(“C”)2.	 Remove	transportation	safety	bolts	by	turning	them	gently.3.	 Fit	the	covers	(supplied	in	the	bag	with	the...

4 - EN
•		 The	specified	voltage	must	be	equal	to	your	mains	voltage.•		 Connection	via	extension	cords	or	multi-plugs	should	not	be	made.
B	A	damaged	power	cable	must	be	replaced	by	a	qualified	electrician.
B	The	appliance	must	not	be	operated	unless	it	is	repaired!	There	is	the	risk	of	electric	shock!
3 Initial preparations for washing
Preparing clothes for washingLaundry	items	with	metal	attachments	such	as,	bras,	belt	buckles	and	metal	buttons	will	damage	the	machine.	Remove	metal	attachments	or...

5 - EN
4 Selecting a Program and Operating Your Machine
Control Panel
1	-	Program	selection	knob	(Uppermost	position	On/Off)
2	-	Display
3	-	Time	delaying	button
4	-	Program	follow-up	indicator
Turning the machine onPlug	in	your	 machine.	 Turn	the	tap	 on	completely.	Check	if	the	hoses	are	connected	tightly.	Place	the	laundry	in	the	machine.	Add	detergent	and	softener.	"Turn	the	program	selection	knob	to	the	program	position	you	wish	to	run."
Program selectionSelect	 the	appropriate	 program...

6 - EN
washing	cycle.	It	is	 recommended	 for	your	 cotton	items	(such	as	bed	sheets,	duvet	and	pillowcase	sets,	bathrobes,	underclothing,	etc.).
• SyntheticsYou	can	wash	your	less	durable	clothes	on	this	program.	Gentler	washing	movements	and	a	shorter	washing	cycle	is	used	compared	to	the	“Cottons”	program.	It	is	recommended	for	your	synthetic	clothes	(such	as	shirts,	blouses,	synthetic/cotton	blended	garments,	etc.).	For	curtains	and	lace,	the	“Synthetic	40”	program	with	pre-wash	and	anti-creasing...

7 - EN
Program selection and consumption table
•	:	Selectable
*	:	Automatically	selected,	not	cancellable.
**:	Energy	Label	programme	(EN	60456)
	***	If	maximum	spin	speed	of	your	machine	is	lower,	selection	may	be	made	until	maximum	spin	speed.
C	 Water	and	power	consumption	may	vary	subject	to	the	changes	in	water	pressure,	water	hardness	and	temperature,	ambient	temperature,	type	and	amount	of	laundry,	selection	of	auxiliary	functions	and	spin	speed,	and	changes	in	electric	voltage.
C	 Programme...

8 - EN
Auxiliary functionsAuxiliary Function Selection ButtonsSelect	the	required	auxiliary	functions	before	starting	the	program.	Furthermore,	you	may	also	select	or	cancel	auxiliary	functions	that	are	suitable	to	the	running	program	without	pressing	the	"Start/Pause"	button.	To	select	or	cancel	the	auxiliary	functions,	the	machine	must	be	at	any	prior	stage	than	the	auxiliary	function	to	be	selected	or	cancelled.	If	the	auxiliary	function	cannot	be	selected	or	cancelled,	light	of	the	relevant...

9 - EN
Changing the delay timeIf	you	want	to	change	the	time	during	the	countdown:
1.	 Press	the	time	delay	button.	Every	time	the	button	is	pressed,	the	time	will	be	increased	in	1-hour	increments.2.	 If	you	wish	to	shorten	the	time	delay,	keep	on	pressing	the	time	delay	button	until	the	time	delay	you	would	like	to	set	appears	on	the	screen.Canceling the time delayIf	you	want	to	cancel	the	time	delay	countdown	and	start	the	program:
1.	 Set	the	Time	Delay	to	zero	or	turn	the	Program	selection	knob	to...

10 - EN
turned	while	the	machine	is	in	child-proof	lock	mode.
Furthermore,	the	lights	on	the	auxiliary	function	buttons	1	and	2	blink	3	times	to	show	how	to	exit	Child-proof	Lock	mode.
To	deactivate	the	childproof	lock:
a)	 Press	the	auxiliary	function	buttons	1	and	2	for	3	sec.	while	any	program	is	running.	While	the	lights	on	the	auxiliary	function	buttons	1	and	2	are	flashing	during	3-second	press	and	hold	process,	C03,	C02	and	C01	labels	will	be	displayed	respectively.	Then,	the	"COF"	label...