BEKO WMB 50831 User Manual

51EN
Programme and consumption table
EN2Auxiliary functions
Programme
Max. Load (kg)Water Consumption (l)Energy Consumption (kWh)Max. Speed***PrewashQuick WashRinse PlusAnti-CreasingRinse HoldSoakingPet hair removal
Selectable temperature range °C
Cottons905662.251600•••••••Cold-90
Cottons605661.451600•••••••Cold-90
Cottons405660.851600•••••••Cold-90
Cotton Economic60**5370.741600•40-60
Cotton Economic60**2.5300.691600•40-60
Cotton Economic40**2.5300.611600•40-60
Daily express905551.901400••Cold-90
Daily...

52EN
Auxiliary function selectionSelect the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme without pressing the Start / Pause button when the machine is operating. For this, the machine must be in a step before the auxiliary function you are going to select or cancel.If the auxiliary function cannot be selected or canceled, light of the relevant auxiliary function will blink 3 times to...

53EN
start time moves up and down on the display. 
C Additional laundry may be loaded during the delayed start period.5.   At the end of the countdown, duration of the selected programme will be displayed. “_” symbol will disappear and the selected programme will start.Changing the Delayed Start periodIf you want to change the time during countdown:1.  Press Delayed Start button. Time will increase by 1 hour each time you press the button.2.  If you want to decrease the delayed start time, press Delayed...

54EN
You can change the auxiliary functions, speed and temperature settings without stopping the programme flow while the programme is running. To do this, the change you are going to make must be in a step after the running programme step. If the change is not compatible, relevant lights will flash for 3 times.
C If the machine does not pass to the spinning step, Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of...

55EN
6 Maintenance and cleaning
Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
Cleaning the detergent drawerClean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time.
1.  Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.
C If more than normal amount of water and...

56EN
1.  Close the taps.2.  Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.3.  Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.4.  Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.
Draining remaining water and 
cleaning...

57EN
c.  When draining of water is finished, close the end by the plug again and fix the hose in its place.d.  Turn the pump filter to take it out.Discharging the water when the product does not have an emergency draining hose:
a.  Place a large container in front of the filter to catch water from the filter.b.  Loosen pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any...

58EN
7 Troubleshooting
Programme cannot be started or selected. 
•  Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel button for 3 seconds to reset the machine to factory settings. (See "Canceling the programme")
Water in the machine.
•  Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the...

59EN
Washing takes longer time than the one specified in the manual.
•  Water pressure is low. >>> Machine waits until taking in adequate amount of water to prevent poor washing quality due to the decreased amount of water. Therefore, the washing time extends.•  Voltage might be low. >>> Washing time is prolonged to avoid poor washing results when the supply voltage is low.•  Input temperature of water might be low. >>> Required time to heat up the water extends in cold seasons. Also, washing time can be...

60EN
Washing performance is poor: Laundry turns gray.
•  Insufficient amount of detergent was used over a long period of time. >>> Use the recommended amount of detergent appropriate for water hardness and t\
he laundry.•  Washing was made at low temperatures for a long time over a long period of time. >>> Select the proper temperature for the laundry to be washed.•  Insufficient amount of detergent is used with hard waters. >>> Using insufficient amount of detergent with hard water causes the soil to...