Beko Wm 6143 Owners Manual

21EN
Auxiliary functions
Auxiliary function selection keys
Select the required auxiliary functions 
before starting the programme.
C Auxiliary function buttons may differ 
according to the model of your 
machine.
Auxiliary function selection
If an auxiliary function that should not 
be selected together with a previously 
selected function is chosen, the first 
selected function will be cancelled and the 
last auxiliary function selection will remain 
active.
For example: If you want to select pre-
wash...

22EN
When the same button is pressed 
again, 6 hours; and if pressed once 
more, 9 hours delay will be selected. If 
the time delaying button is pressed one 
more time, time delaying function will 
be cancelled. Set the time delay as you 
require. 
4.  Delayed operation of the selected 
programme is started by pressing 
the “Start/Pause/Cancel” button after 
making the time delay selection. 
C More laundry may be loaded/removed 
during the time delay period.
Changing and cancelling the time 
delay.
1....

23EN
C  The spin speed and temperature which 
are selected first will keep on being 
valid even if the position of the spin 
speed or temperature selection knob is 
changed. Press “Start/Pause/Cancel” 
button and switch the machine to 
“Pause” mode in order to change the 
spin speed or temperature. New spin 
speed or temperature can be selected.  
Adding/removing laundry in standby 
mode
If you want to add more laundry into the 
machine after the washing cycle has 
started, put the machine into “Pause”...

24EN
6 Maintenance and cleaning
Service life of the product extends and 
frequently faced problems decrease if 
cleaned at regular intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular 
intervals (every 4-5 washing cycles) 
as shown below in order to prevent 
accumulation of powder detergent in time.
1.  Press the dotted point on the siphon 
in the softener compartment and pull 
towards you until the compartment is 
removed from the machine.
C If more than normal amount of water...

25EN
1. Close the taps.
2.  Remove the nuts of the water intake 
hoses to access the filters on the water 
intake valves. Clean them with an 
appropriate brush. If the filters are too 
dirty, take them out by means of pliers 
and clean them.
3.  Take out the filters on the flat ends of 
the water intake hoses together with 
the gaskets and clean thoroughly under 
running water.
4.  Replace the gaskets and filters carefully 
in their places and tighten the hose 
nuts by hand.
Draining remaining water and...

26EN
is emptied, repeat the above procedure 
to drain the water in the machine 
completely.
c.  When draining of water is finished, 
close the end by the plug again and fix 
the hose in its place.
d.  Turn the pump filter to take it out.
Discharging the water when the product 
does not have an emergency draining 
hose:
a.  Place a large container in front of the 
filter to catch water from the filter.
b.  Loosen pump filter (anticlockwise) until 
water starts to flow. Fill the flowing 
water into the...

27EN
7 Troubleshooting
Programme cannot be started or selected. 
•  Washing machine has switched to self protection mode due to a supply problem 
(line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel 
button for 3 seconds to reset the machine to factory settings. (See "Canceling the 
programme")
Water in the machine.
•  Some water might have remained in the product due to the quality control 
processes in the production. >>> This is not a failure; water is not harmful to...

28EN
Loading door cannot be opened.
• Door lock is activated because of the water level in the machine. >>> Drain the 
water by running the Pump or Spin programme.
•  Machine is heating up the water or it is at the spinning cycle. >>> Wait until the 
programme completes.
•  Child lock is engaged. Door lock will be deactivated a couple of minutes after the 
programme has come to an end. >>> Wait for a couple of minutes for deactivation 
of the door lock.
Washing takes longer time than the one specified in...

29EN
Machine does not switch to spinning step.
• There might be an imbalance of laundry in the machine. >>> Automatic 
unbalanced load detection system might be activated due to the unbalance\
d 
distribution of the laundry in the drum.
C Machine does not switch to spinning step when the laundry is not evenly \
distributed in the drum to prevent any damage to the machine and to its 
surrounding environment. Laundry should be rearranged and re-spun.
•  The machine will not spin if water is not drained...

30EN
Washing performance is poor: Clothes smell unpleasantly.
• Odours and bacteria layers are formed on the drum as a result of continuous 
washing at lower temperatures and/or in short programmes. >>> Leave the 
detergent drawer as well as the loading door of the machine ajar after e\
ach 
washing. Thus, a humid environment favorable for bacteria cannot occur i\
n the 
machine.
•  Regular drum cleaning is not applied. >>> Clean the drum regularly. For this, 
please see "Cleaning the loading door...