BEKO WKL 13560 K User Manual

							EN17
Program selection and consumption table
•	:	Selectable
*	:	Automatically	selected,	not	cancellable.
**:	Energy	Label	programme	(EN	60456)
Water and power consumption and programme duration may differ from the t\
able 
shown, subject to changes in water pressure, water hardness and temperat\
ure, 
ambient temperature, type and amount of laundry, selection of auxiliary \
functions, 
and fluctuations in the supply voltage.
C The auxiliary functions in the table may differ according to the model o\
f your 
machine.
Programme
Max. Load (kg)
Programme Duration (~min)
Water Consumption (l)
Energy Consumption (kWh)
Prewash
Rinse Plus
Rinse Hold
SS reduction 
No Spin
No Heat
Cottons 903.5136 430.97••••••
Cottons 60*3.5135 430.66••••••
Cottons 403.5136 40.2 0.53••••••
Super 403.5165 500.17•••
Synthetics 602.5116 500.78••••••
Synthetics 402.5108 500.51••••••
Delicate 30269 550.34•••••
Woollens 401.570550.35•••••
Hand wash 30155 400.20•••
Mini 302.535300.21•••
 
						

							EN18
Auxiliary functions
Auxiliary function selection keys
•	 Desired	auxiliary	function	depending	on the program is selected.
•	 Some	combinations	cannot	be	 selected together.
•	 Warning	signal	on	the	selected	 auxiliary function will light up.
Auxiliary function buttons may differ 
according to the model of your machine.
Auxiliary function selection
If an auxiliary function that should not 
be selected together with a previously 
selected function is chosen, the first 
selected function will be cancelled and 
the last auxiliary function selection will 
remain active.
Auxiliary function that is not compatible 
with the program cannot be selected. 
(see,	“Program	Selection	Table”)
Pre-wash
A pre-wash is only worthwhile for heavily 
soiled laundry. Without pre-wash you 
save energy, water, detergent and time.
C	 Pre-wash	without	detergent	is	 recommended for lace and curtains. 
Less detergent should be put in the 
main wash compartment as loose 
knit	fabrics	(lace)	foam	too	much	
due to its meshed structure.
Rinse Plus
With this function, you can increase the 
number of current rinsing steps. Thus, 
sensitive skins’ risk of being affected by 
the remainder detergent on the clothes 
will be decreased.
Rinse hold
If you do not want to unload your 
clothes immediately after the cotton, 
synthetics, woolen and delicate fabrics 
program, you may release your clothes 
inside the machine in the last rinsing 
water by pressing the rinse hold button 
in order to prevent your clothes become 
wrinkled. After this process you may 
spin your laundry by pressing “Start/
Pause/Cancel”	button	or	you	may	end	 the	program	by	pressing	“Start/Pause/
Cancel”	button	for	3	sec.
• 
In the machines equipped with spin 
speed selection knob or button, you 
can spin by selecting the desired 
spin	speed	and	press	“Start/Pause/
Cancel”	button.
•  As for machines not equipped with 
a spin speed selection knob, you 
can end the program without a 
spin cycle by pressing the “Start/
Pause/Cancel”	button	and	draining	
the water. If you wish your clothes 
be spun, you can spin them by 
selecting	“pump+spin”	program.	
Spin speed reduction
You	may	use	the	speed	reduction	
button whenever you wish to spin 
your clothes below the maximum spin 
speed. When speed reduction button 
is pressed, spin speed will be at the 
minimum rpm given on the panel.
No spin
You	may	use	this	program	if	you	do	not	
want to spin your clothes at the end of 
cottons, synthetics, woolen or delicate 
programs.
No Heat
If you wish to wash your clothes in cold 
water, you can use this program.
Starting the Program
1.	 Press	“Start/Pause/Cancel”	button	 to start the program.
2.	 “Start/Pause/Cancel”	button	will	 light up to indicate that the program 
has started.
3.	 The	door	is	locked	and	the	“Lid”	 light fades.
Progressing a program
Progress	of	a	running	program	is	shown	
through the program follow-up indicator.
• At the beginning of every program 
step, the relevant indicator lamp will 
light up and light of the completed 
step will turn off. The symbol that is 
lit up at the far right of the series of 
symbols indicates the step that is 
being carried out.
 
						

							EN19
The	“Wash”	light	on	the	program	follow-
up indicator illuminates when “Start/
Pause/Cancel”	button	is	pressed	after	
selecting the washing program. The 
“Program	finished”	lamp	illuminates	
and	the	“Wash”	light	will	fade	when	the	
program	comes	to	an	end.	The	“Lid”	
light	flashes.	Meanwhile,	the	door	will	
stay locked for your safety and when it 
is	safe	to	open,	the	“Lid”	and	“Program	
Finished”	lights	remain	on.
You	can	put	your	machine	into	“Pause”	
mode	by	pressing	the	“Start/Pause/
Cancel”	button	when	it	is	operating.	
In	this	case,	the	“Start/Pause/Cancel”	
light will flash. Some changes in 
program settings can be made in pause 
mode	(See.	Changing	a	Program)	
and	if	“Pause”	mode	is	entered	at	an	
appropriate step of the program, the 
adding laundry function may be used. 
(See,	Adding	and	taking	out	laundry).	
Press	“Start/Pause/Cancel”	button	
again	to	return	to	the	“Wash”	mode	
from	“Pause”	mode.	In	this	case	the	
“Start/Pause/Cancel”	button	will	light	
up continuously and the machine will 
resume operating from the step it was 
paused.
•If the machine is not spinning, the program may be in rinse hold mode 
or the automatic spin correction 
system has been activated because 
of unbalanced distribution of laundry 
in the machine.
Changing the program after 
the program has started
You	can	use	this	feature	after	your	
machine has started to wash different 
textile groups in the same batch 
of clothes under higher or lower 
temperatures.
For	example;
Press	and	hold	the	“Start/Pause/
Cancel”	button	for	3	seconds	to	
“Cancel”	the	program	in	order	to	
select	“Cottons	40”	program	instead	of	 “Cottons	60”	program.
Select	the	“Cottons	40”	program	by	
rotating the program knob.
Press	“Start/Pause/Cancel”	button	to	
start the program.
C 
The program which is selected 
first will go on even if the program 
selection button is moved and 
another program mode is selected 
while the machine is operating. 
You	must	cancel	the	ongoing	
program in order to change the 
washing	program.	(See,	Canceling	a	
Program)
Selecting or cancelling an auxiliary 
function/temperature/spin speed
1.	 Press	the	“Start/Pause/Cancel”	 button to switch the machine to 
“Pause”	mode.
2.  Change the auxiliary function’s 
temperature and spin speed.
Press	“Start/Pause/Cancel”	button	to	 start the program.
C   The selection to be made must be 
appropriate. For example, if your 
machine is on the main wash cycle, 
you may select additional rinse 
auxiliary function, but you cannot 
select pre-wash.
C   The spin speed and temperature 
which are selected first will keep on 
being valid even if the position of the 
spin speed or temperature selection 
knob	is	changed.	Press	the	“Start/
Pause/Cancel”	button	and	switch	
the	machine	to	“Pause”	mode	in	
order to change the spin speed or 
temperature. New spin speed or 
temperature can be selected.
Adding/removing laundry in standby 
mode
If you want to add more laundry into the 
machine after the washing cycle has 
started,	put	the	machine	into	“Pause”	
mode	by	pressing	the	“Start/Pause/
Cancel”	button.	The	“Lid”	lamp	on	the	
program follow-up indicator will light up 
 
						

							EN20
steadily after 1-2 minutes if the water 
level in the machine is suitable. Laundry 
may be added or taken out by opening 
the	door.	If	the	“Lid”	lamp	does	not	
light up continuously at the end of this 
time, the water level in the machine 
is not suitable and laundry cannot be 
added.	You	can	resume	the	program	
by	pressing	the	“Start/Pause/Cancel”	
button again.
Child-proof lock
There is a childproof lock to prevent 
any program interruption because of 
pressing the keys while the program is 
on. In order to activate the childproof 
lock, press on the 1st and 2nd 
auxiliary function keys from the left 
simultaneously for 3 seconds after 
the washing program has started. 
1st auxiliary function light will flash 
continuously.
To start a new program after the 
program is over or to interfere the 
program, childproof lock should be 
deactivated. To deactivate the child-
proof lock, press the same buttons for 
3 sec.
Ending the program through 
canceling
The program which is selected first will 
keep on going even if the position of the 
program selection button is changed. A 
new program can be selected or started 
after	“Program	is	cancelled”	in	order	to	
change the washing program.
To	cancel	any	selected	program;
•		Press	“Start/Pause/Cancel”	button	
for 3 seconds. The machine starts 
to	discharge	the	water.	“Wash”	and	
“Program	Finished”	lights	will	light	
up.
•	 “Start/Pause/Cancel”	and	“Wash”	 lights will go off after discharging 
process	is	over	and	the	“Lid”	light	
will start flashing.
•	 “Lid”	lamp	will	light	up	continuously	 when	the	door	is	unlocked.		You	can	
select and start a new program. •	 If	the	program	is	cancelled	in	the	
middle	of	the	process,	“Wash”	
and	“Program	Finished”	lights	will	
light up. The machine can drain 
all the water or can take in water 
for 3 times at most to cool down 
the clothes and complete draining 
process.
•	 When	the	water	discharging	process	 is	completed,	the	“Wash”	light	will	
go	off,	“Program	Finished”	light	
will	light	up	and	the	“Lid”	light	will	
continuously flash until the door 
is	unlocked.	You	can	make	a	new	
program	selection	when	the	“Lid”	
light is illuminated continuously.
End of Program
The	“Program	Finished”	lamp	on	the	
program follow-up indicator will light up 
when the program comes to an end. 
The lid is unlocked 2 minutes later, the 
“Program	Finished”	and	“Lid”	lamps	will	
light up continuously. The machine is 
now ready for a second cycle.
If any key is pressed when the machine 
is at the end of the program or if 
the position of the selection knob is 
changed,	the	“Program	Finished”	light	
will	go	off	and	only	the	“Lid”	lamp	will	
remain	as	lit.	Meanwhile,	if	the	door	is	
still	locked,	the	“Lid”	light	will	continue	
flashing until the door is opened.
Press	the	“On/Off”	button	to	shut	down	
the machine.
 
						

							EN21
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3.  Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2.  Select the programme and the 
temperature.
3.	 If	required	(according	to	your	 machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4.  Close the loading door.
5.	 Press	Start/Pause/Cancel	button.
Canceling a program
•	 Press	“Start/Pause/Cancel”	button	 for 3 seconds. The machine starts 
to	discharge	the	water.	“Wash”	and	
“Program	Finished”	lights	will	light	
up.
•	 “Start/Pause/Cancel”	and	“Wash”	 lights will go off after discharging 
process	is	over	and	the	“Lid”	light	
will start flashing. 
•	 If	the	program	is	cancelled	in	the	 middle	of	the	process,	“Wash”	
and	“Program	Finished”	lights	will	
light up. The machine can drain 
all the water or can take in water 
for 3 times at most to cool down 
the clothes and complete draining 
process. When water discharging 
process	is	completed,	“Wash”	light	
will	go	off,	“Program	Finished”	light	
will	light	up	and	the	“Lid”	light	will	
continuously flash until the door 
is	allowed	to	be	opened.	You	can	
make a new program selection when 
the	“Lid”	light	is	lit	continuously.
Adding more laundry
You	may	add	more	laundry	into	the	
machine at the beginning of washing. C		 Machine	allows	adding	more	laundry	
during a later step only if the water 
level is low enough to open the 
loading door or if the temperature in 
the machine is low enough.
In order to add laundry after the start-up 
of	the	program:
1.	 Press	Start/Pause/Cancel	button.	 Wait until the door is allowed 
to	open.	“Lid”	lamp	will	light	up	
continuously when the door is 
allowed to open.
2.	 Open	the	loading	door	and	put	in	 more laundry.
3.  Close the loading door.
4.	 Press	Start/Pause/Cancel	button.
Program is in rinse hold mode
C   After the machine fills with water in 
the final rinse step, clothes can be 
soaked in the machine as long as 
desired.
When it reaches this position while the 
machine	is	running,	the	“Start/Pause/
Cancel”	light	will	flash.	
In the machines equipped with spin 
speed selection knob, you can spin by 
selecting the desired spin speed and 
press	“Start/Pause/Cancel”	button.
As for machines not equipped with a 
spin speed selection knob, you can 
end the program without spinning by 
pressing	the	“Start/Pause/Cancel”	
button	to	drain	the	water.		You	may	spin	
your clothes whenever you wish to by 
selecting the spin program.
Re-spinning the laundry
The control system for an unbalanced 
load can pause the spinning in cases 
when the distribution of the laundry in 
the drum is not balanced.
If	you	want	to	re-spin	the	clothes:
1.  Rearrange the previously placed 
clothes in machine.
2.	 Select	Spin+Pump	program.
6  Quick instructions for daily use
 
						

							EN22
3. Set the spin speed if spin speed 
adjustment is available on your 
machine.
4.	 Press	“Start/Pause/Cancel”	button.	
After the program is finished
1.	 “Program	finished”	lamp	will	light	 up on the program follow-up 
indicator. The lid can be opened 
after	2	minutes	when	the	“Program	
Finished”	and	“Lid”	lamps	light	up	
continuously.  
2.	 Press	the	On/Off	button	to	shut	 down the machine.
3.  Turn the water tap off.
4.  Eliminate any folding of the rubber 
seal on the loading door and check 
for impurities.
5.  Leave the loading door and 
detergent drawer open to dry.
 
						

							EN23
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C  If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2.  Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate brush to avoid touching 
the residues in the drawer when 
cleaning.
3.  Replace the drawer into its housing 
after cleaning.  Check if the siphon 
is in its original location.
The door and the drum
After	each	wash:
•	 Check	if	there	are	any	foreign	
substances in the drum.
•	 Open	the	hole	in	the	bellow	with	the	 aid of a toothpick if it is clogged.
C  Foreign metal substances in your 
machine can cause rust stains. In 
such	cases:
  Clean the drum with a stainless steel 
cleaning agent. Never use steel wool 
or wire wool.
Outer cabinet and control 
panel
When	necessary:
•	 Wipe	the	exterior	panels	of	your	
machine with soapy water or mild 
detergent. Dry it with a soft cloth.
•	 Use	only	a	soft	and	damp	cloth	to	 clean the control panel.
C  Never use a sponge or scrubbing 
material. These will damage the 
painted and plastic parts.
Inlet water filters
There is a filter at the end of each 
water intake valve at the back side of 
the machine and also at the end of 
each water intake hose where they 
are connected to the tap. These filters 
prevent the foreign substances and dirt 
in the water to enter into the machine. 
Filters should be cleaned as they get 
dirty.
•	 Close	the	taps.
•	 Remove	the	nuts	of	the	water	intake	
hoses to clean the surfaces of the 
filters on the water intake valves with 
an appropriate brush.
•	 If	the	filters	are	very	dirty,	you	can	 pull them out by means of pliers and 
clean them.
•	 Take	out	the	filters	on	the	flat	 ends of the water intake hoses 
together with the gaskets and clean 
thoroughly under streaming water.
•	 Replace	the	gaskets	and	filters	 carefully and tighten the hose nuts 
by hand.
7  Cleaning and care
 
						

							EN24
Draining any remaining water 
and cleaning the pump filter
Filter system in your machine prevents 
solid items such as buttons, coins and 
fabric fibers clogging the pump propeller 
during discharging of the washing 
water. Thus, a good water discharger is 
achieved and the pump life is extended.
•		 If	your	machine	fails	to	drain	the	water, the pump filter may be 
clogged.	You	may	have	to	clean	
it every 2 years or whenever it is 
blocked plugged. Water must be 
drained off to clean the pump filter. 
In addition, water may have to be 
drained off completely in the following 
cases:
•		 before	transporting	the	machine	 (e.g.	when	moving	house)
•		 when	there	is	the	danger	of	frost
In order to clean the dirty filter and 
discharge	the	water;
1- Disconnect or unplug the machine 
from the power supply.
A  There may be water at 90°C in the 
machine. Therefore, the filter must 
be cleaned only after the inside 
water is cooled down to avoid 
hazard of scalding.
2-	Open	the	filter	cap.	The	filter	cap	
may be composed of one or two pieces 
according to the model of your machine.
If it is composed of two pieces, press 
the tab on the filter cap downwards and  pull the piece out towards yourself.
If it is composed of one piece, hold it 
from both sides and open it by pulling 
out.
3- An emergency drain hose is supplied 
with	some	of	our	models.	Others	are	not	
supplied with this item.
If your product is supplied with an 
emergency drain hose, do the following 
as	shown	in	the	figure	below:
•		 Pull	out	the	pump	outlet	hose	from	
its housing.
•		 Place	a	large	container	at	the	end	of	 the hose. Drain the water off into the 
container by pulling out the plug at 
the end of the hose. If the amount 
of water to be drained off is greater 
than the volume of the container, 
replace the plug, pour the water out, 
then resume the draining process.
•		 After	draining	process	is	completed,	
 
						

							EN25
replace the plug into the end of the 
hose and fit the hose back into its 
place.
If your product is not supplied with an 
emergency drain hose, do the following 
as	shown	in	the	figure	below:
•		 Place	a	large	container	in	front	of	the	 filter to receive water flowing from 
the filter.
•		 Loosen	pump	filter	(anticlockwise)	 until water starts to flow out of it. 
Direct the flowing water into the 
container you have placed in front 
of	the	filter.	You	can	use	a	piece	of	
cloth to absorb any spilled water.
•		 When	there	is	no	water	left,	turn	the	 pump filter until it is completely loose 
and remove it.
•		 Clean	any	residues	inside	the	filter	 as well as fibers, if any, around the 
propeller region.
•		 If	your	product	has	a	water	jet	 feature, be sure to fit the filter into 
its housing in the pump. Never force 
the filter while replacing it into its 
housing. Fit the filter fully into its 
housing;	otherwise,	water	may	leak	
from the filter cap.
4- Close the filter cap.
Close the two-piece filter cap of your 
product by pushing the tab on it.
Close the one-piece filter cap of your 
product by fitting the tabs on the bottom 
into their positions and pushing the 
upper part of it.
 
						

							EN26
ProblemCause Explanation / Suggestion
Program	
cannot be 
started or 
selected. Machine	may	have	
switched to self 
protection mode due to 
an infrastructure problem 
(such	as	line	voltage,	
water	pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/
Cancel”	button	for	3	seconds.	(see,	Cancelling	
a	Program)
Water in the 
machine. There may be some water 
in your machine when you 
receive it. This is from the 
quality control process 
and is normal.
It is not harmful to your machine.
There is water 
coming from 
the bottom of 
the machine. There might be problems 
with hoses or the pump 
filter. Be sure the seals of the water inlet hoses are 
securely fitted.
Tightly attach the drain hose to the waste pipe 
or sink.
Make	sure	that	the	pump	filter	is	completely	
closed.
Machine	does	
not fill with 
water. Tap may be turned off.
Open	the	inlet	water	taps	fully.
Water inlet hose might be 
bent. Straighten the water intake hose.
Water inlet filter might be 
clogged. Clean the water intake filter.
The door may be ajar. Close the door.
Machine	does	
not discharge 
water. Water outlet hose might 
be clogged or twisted.
Clean or straighten the hose.
Pump	filter	may	be	
clogged. Clean the pump filter.
Machine	
vibrates or 
shakes. Machine	feet	might	
require adjustment.
Adjust the machine feet.
Transportation safety 
bolts might have not been 
removed. Remove the transportation safety bolts.
There may be a small 
amount of laundry in the 
machine. Add more laundry to the machine.
The machine may be 
overloaded or the clothes 
may be distributed 
unevenly. Reduce the amount of laundry in the machine 
or balance the load by hand.
There machine might be 
touching a solid surface Ensure that nothing touches the machine.
Machine	
stopped 
shortly after 
the program 
started. Machine	can	stop	
temporarily due to low 
voltage.
It will resume operating when the voltage is 
back to the normal level.
8  Troubleshooting