BEKO WKL 13540 K User Manual

EN17
Program selection and consumption table
•	:	Selectable
*	:	Automatically	selected,	not	cancellable.
**:	Energy	Label	programme	(EN	60456)
Water and power consumption and programme duration may differ from the t\
able 
shown, subject to changes in water pressure, water hardness and temperat\
ure, 
ambient temperature, type and amount of laundry, selection of auxiliary \
functions, 
and fluctuations in the supply voltage.
C The auxiliary functions in the table may differ according to the model o\
f...

EN18
Auxiliary functions
Auxiliary function selection keys
•	 Desired	auxiliary	function	depending	on the program is selected.
•	 Some	combinations	cannot	be	 selected together.
•	 Warning	signal	on	the	selected	 auxiliary function will light up.
Auxiliary function buttons may differ 
according to the model of your machine.
Auxiliary function selection
If an auxiliary function that should not 
be selected together with a previously 
selected function is chosen, the first 
selected function will be...

EN19
The	“Wash”	light	on	the	program	follow-
up indicator illuminates when “Start/
Pause/Cancel”	button	is	pressed	after	
selecting the washing program. The 
“Program	finished”	lamp	illuminates	
and	the	“Wash”	light	will	fade	when	the	
program	comes	to	an	end.	The	“Lid”	
light	flashes.	Meanwhile,	the	door	will	
stay locked for your safety and when it 
is	safe	to	open,	the	“Lid”	and	“Program	
Finished”	lights	remain	on.
You	can	put	your	machine	into	“Pause”	
mode	by	pressing	the	“Start/Pause/
Cancel”...

EN20
steadily after 1-2 minutes if the water 
level in the machine is suitable. Laundry 
may be added or taken out by opening 
the	door.	If	the	“Lid”	lamp	does	not	
light up continuously at the end of this 
time, the water level in the machine 
is not suitable and laundry cannot be 
added.	You	can	resume	the	program	
by	pressing	the	“Start/Pause/Cancel”	
button again.
Child-proof lock
There is a childproof lock to prevent 
any program interruption because of 
pressing the keys while the program is 
on....

EN21
Preparation
1. Turn the tap on completely. Check if 
the hoses are connected tightly.
2.	 Place	the	laundry	in	the	machine.
3.  Add detergent and softener.
Starting
1.	 Press	the	“On/Off”	button.
2.  Select the programme and the 
temperature.
3.	 If	required	(according	to	your	 machine’s	model):
–	 select	any	auxiliary	function,
–	 adjust	the	spin	speed,
–	 set	the	time	delay,
4.  Close the loading door.
5.	 Press	Start/Pause/Cancel	button.
Canceling a program
•	 Press	“Start/Pause/Cancel”	button...

EN22
3. Set the spin speed if spin speed 
adjustment is available on your 
machine.
4.	 Press	“Start/Pause/Cancel”	button.	
After the program is finished
1.	 “Program	finished”	lamp	will	light	 up on the program follow-up 
indicator. The lid can be opened 
after	2	minutes	when	the	“Program	
Finished”	and	“Lid”	lamps	light	up	
continuously.  
2.	 Press	the	On/Off	button	to	shut	 down the machine.
3.  Turn the water tap off.
4.  Eliminate any folding of the rubber 
seal on the loading door and check 
for...

EN23
Detergent drawer
Remove any powder residue buildup in 
the	drawer.	To	do	this;
1.	 Press	the	dotted	point	on	the	siphon in the softener compartment 
and pull towards you until the 
compartment is removed from the 
machine.
C  If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, 
the siphon must be cleaned.
2.  Wash the dispenser drawer 
and the siphon with plenty of 
lukewarm water in a washbasin. 
Wear protective gloves or use an 
appropriate...

EN24
Draining any remaining water 
and cleaning the pump filter
Filter system in your machine prevents 
solid items such as buttons, coins and 
fabric fibers clogging the pump propeller 
during discharging of the washing 
water. Thus, a good water discharger is 
achieved and the pump life is extended.
•		 If	your	machine	fails	to	drain	the	water, the pump filter may be 
clogged.	You	may	have	to	clean	
it every 2 years or whenever it is 
blocked plugged. Water must be 
drained off to clean the pump...

EN25
replace the plug into the end of the 
hose and fit the hose back into its 
place.
If your product is not supplied with an 
emergency drain hose, do the following 
as	shown	in	the	figure	below:
•		 Place	a	large	container	in	front	of	the	 filter to receive water flowing from 
the filter.
•		 Loosen	pump	filter	(anticlockwise)	 until water starts to flow out of it. 
Direct the flowing water into the 
container you have placed in front 
of	the	filter.	You	can	use	a	piece	of	
cloth to absorb any spilled...

EN26
ProblemCause Explanation / Suggestion
Program	
cannot be 
started or 
selected. Machine	may	have	
switched to self 
protection mode due to 
an infrastructure problem 
(such	as	line	voltage,	
water	pressure,	etc.).
Reset	your	machine	by	pressing	“Start/Pause/
Cancel”	button	for	3	seconds.	(see,	Cancelling	
a	Program)
Water in the 
machine. There may be some water 
in your machine when you 
receive it. This is from the 
quality control process 
and is normal.
It is not harmful to your machine.
There...