Beko Wkd 24500 Ts Users Manual

							
15
Pressing “On/Off”
By pressing “On/Off” button you can make your ma-
chine ready for selecting program. When “On/Off” key is 
pressed “door” led will light on meaning “door can open”. 
Press “On/Off” key again for turning your machine off. 
Pressing “On/Off” does not mean program started opera
-
tion. You must press “Start/Pause/Cancel” for starting the 
program. 
Child-proof lock
During washing laundry in order to maintain that program 
progress is not affected by pressing keys by children 
there is child-proof lock. To enable child-proof lock, after 
washing begins, press Express and Rinse Plus function 
buttons together simultaneously for three seconds. Pre-
wash additional function led will always blink. 
After program ends in order to start a new program or 
alter the program you have to disable child-proof lock. To 
do this press same buttons for three seconds and Child-
proof lock led will be off.
Function Selection
Additional functions selectable according to selected 
program can be selected by pressing related key. Led of 
selected function will be on.
If not selected together some additional functions go off 
when it is not selected with other one. For example; when 
using cotton program, exspress and rinse plus auxillary 
functions can not be selected together. After selecting ex
-
press program, if rinse plus key is pressed fast program 
will be on and express function led will go off.
Program Progress
After machine starts operation relevant program led on 
program progress display will be on. When a step is 
completed that step’s led is off and next step’s led is on. 
When “On/Off button is pressed “door” led will be on. Af
-
ter washing program is selected when “Start/Pause/Can-
cel” key is pressed “Washing” led on program progress 
display will be on. At the final step “Spin cycle” led is on.
 
						

							
16
When program is completed “Ready” led will be on again. 
During machine operation you can press “Start/Pause/
Cancel” key for getting machine to “Pause” position. In 
this case “Start/Pause/Cancel” led will blink. 
Changing Program 
You can use this feature for washing laundry in the same 
textile group for washing at lower or higher temperatures. 
For example, instead of Cotton60, Cotton40 can be used. 
For selecting Cotton40 instead of Cotton60 by pressing 
“Start/Pause/Cancel” key machine is switched to pause 
position. Program knob is turned for selecting Cotton40 
program. 
Even when the program selection button is changed dur-
ing the program initially selected program will be execut-
ed. For changing washing program continuing program 
must be cancelled. (See Cancelling a program)
For selecting auxillary functions or spin speed necessary 
changes can be performed after pressing Start/Pause/
Cancel button. Although selected auxillary functions must 
be compatible with washing program. For example when 
your machine is intensive program you can select ad-
ditional rinse plus function but you can not select express.
Adding laundry
If you want to add laundry to your machine after program 
begins press Start/Pause key for switching machine to 
pause mode. If water level in the machine is appropriate 
“door” led on program progress display is on and laundry 
can be added to the machine. If “door” led is not on after 
one minute than water level in the machine is not ap-
propriate and laundry can not be added. You can press 
“Start/Pause/Cancel” key for continuing program. 
Time delay for program start
Using time delay key you can delay the starting of the 
selected program for 3 hours, 6 hours or 9 hours. 
When time delay key is pressed once 3hours delay is 
adjusted and led will light on. If same key is pressed once 
more delay is 6hours, and if it is pressed once more 9 
hours delay is selected. If time delay key is pressed again 
delay is cancelled. After the selection of time delay when 
“Start/Pause/Cancel” is pressed program can be started 
with delay. During delay period door can be opened or 
laundry can be added 
After time delay is initiated by pressing “Start/Pause/
Cancel” you can switch machine to “Pause” mode and 
change delay time. 
 
						

							
17
Canceling a Program 
For canceling a program “Start/Pause/Cancel”  key is 
pressed for three seconds. After this period “Start/Pause/
Cancel”  and all other leds will be off .You can select a 
new program and start washing.
If cancel task is performed during washing “Spin” led on 
display will light on, machine will pump and when “Spin” 
led is off “door” led will be on, door can be opened and 
new program can be selected. 
Even program selection button is changed during the 
program initially selected program will be executed. For 
changing washing program “Canceling a program” must 
be performed afterwards new program can be selected 
and started 
After machine starts operation even if spin speed or 
washing temperature is changed, initial speed and tem-
perature is valid. In order to change spin speed or tem-
perature after pressing “Start/Pause/Cancel”  new cycle 
or temperature can be selected. 
End of Program
When program ends “ door” led will light on and door can 
be opened and machine is ready for next washing. Press 
“On/Off” for turning machine off. 
Emptying Laundry 
After program ends machine automatically stops. Turn off 
tap water. Pull the handle and open loading door. Turn off 
your machine by pressing “On/Off”. After taking laundry 
out keep the loading door open and let the drum ventilate. 
Check the bellow and clean. 
 
						

							
18
Detergent Dispenser
Powder detergent residue may accumulate in drawer 
after a while. In order to clean detergent drawer press the 
marked point of the siphon on softener compartment and 
push the drawer towards yourself. Wash the drawer with 
water 
Siphon
Do not neglect cleaning suction cup when it becomes 
soiled. In order take suction cup out first take detergent
drawer out. Clean it in order to eliminate blocking by soft-
ener residue. After cleaning place suction cup to its place 
and make sure it is placed properly. 
Water Entrance Filters
There is a filter at each flat end where water inlet hose is
connected to tap and at each of water inlet valve placed  behind the machine. These filters blocks entrance of
foreign objects and dirts to the machine. Filters must be 
cleaned regularly to avoid clogging. For doing this, turn 
off tap water. Pull out water inlet hoses. Clean the top 
of the water inlet valve filter with a brush. If filters are
extremely clogged you can pull it out with a pincer. You 
can take out the flat side of water inlet hoses with its seal
and clean with tap water. (2 filters in Single water inlet
machines, 4 filters in double water inlet machines)
Hose
There is risk of freezing in cold region, if your machine is 
placed in a cold place remaining water in hoses must be 
drained with pump filter when machine is not used. Water
inlet hoses can be drained by taking it out from tap. 
5Care and maintanence
 
						

							
19
Cleaning Pump Filter 
There is filter system maintaning long lifetime of pump by
blocking foreign objects like button, cloth fiber enter to the
pump during drain of washing water. It is useful to clean 
the filter when it is soiled.
In order to do this:
Unplug your machine. Open the filter at bottom right cor
-
ner by pressing marked space on the lid.
Hot water risk: There might be 15 lt., 90°C hot water in 
the drum. Open the filter carefully.Before opening the filter drain the water with drain hose.
Pull out the drain hose from its place. Prepare a suitable 
container and open the tap of hose. After water is drained 
place the tap properly. Open the filter by turning and
drain the remaining water (max30ml) to filter tap.  Clean
remaining foreign object in the filter. When finished turn
in clockwise direction and close. Close the filter tap by
pushing.
Caution!
If the filter and hose tap does not fit, it leaks water.
 
						

							
20
      Installation
If your system is not ready, let a certified plumber make it 
ready.  
1.  Removing the transportation safety bolts
Before the washing machine is operated, the transit bars 
must be removed! In order to do this:
1. Loosen “C” bolts by rotating them counter clockwise 
with a suitable spanner 
2. Remove transportation safety bolts by turning. 
3. Place “P” plastic covers onto the openings of transpor-
tation locks by rotating in direction of arrow and pushing. 
Attention please! Keep the transit bars for using when 
machine is to be transported again. Always transport your 
machine with transportation locks. 
2. Leveling the feet
In order to operate your machine without noise and 
vibration it must be properly on balance. Four feet of your 
machine can be adjusted. First loosen the plastic counter 
bolt. Tighten the counter bolt after adjusting the feet for 
leveling your machine.
3. Water Connections 
a) Water Inlet Hose 
Your machine is connected to water supply by special hoses supplied by the machine. Red hose or hose written red on it is hot water inlet, blue hose or hose written blue on it is cold water inlet.
There are plastic seals (4 for double water inlet mod-els, 2 for single water inlet models) on hose or plastic bag for eliminating any leakage in connections points. These seals must be used on each side of the con-
6
 
						

							
21
nection. Seals on machine side must be connected 
filter cannal.
After connecting the hose, check all connections for leaks In order to eliminate any risk due to water leak-
age keep the taps off when machine is not used.
 
Your machine will operate efficiently if the water from
tap is minimum 1 and maximum 10 bars. Practically 1 bar means 8 liters of water in one minute when tap is fully on. 
Connect hose to the machine. Tighten bolts with hand 
power, do not use spanner.
Double inlet models can be used with blind cap as a single inlet machine. Connect blind cap to hot water inlet. Seal must be for stopping water leakage.
Do not connect single inlet machine to hot water. If 
machine is connected with Y part to a double inlet 
and over 40˚C for single inlet machines, machine may switch to protection mode.
b)  Water drain hose
Water drain hose could be placed either at the side of the 
bath tub, or directly to the drain. The hose should not be 
bent. Water drain hose should be secured with the holder 
so that it would not fall down on the ground.
The hose should be placed between 40 and 100 cm. from 
the ground.
Water drain hose could be placed directly to the drain 
water inlet.
 
						

							
22
4. Electrical connection
Connect the power cord to the appropirate electrical 
system which is being supported by the maximum voltage 
and current rating indicated on the rating plate placed 
inside the kick plate.
Look! Page 1, Steps before operating Fullautomatic 
Washing Machine and safety precautions.
Make sure that you have grounded power outlet. 
Attention! Before any operation of the machine check the 
following.
• Did you close the front door?
• Is the tap open?
• Is water drain hose placed properly?
• Is power connected?
 
						

							
23
      Before calling service
You turned the machine on, but the leds are off on 
the panel.
Check the grounding on the power cable or a blown fuse. 
Check the front door proper closure.
Machine does not take water.
Check the front door for proper closure. Either taps are 
closed or water intake filters are clogged.
Taken water is directly discharged.
Check if the discharge hose placed as described in the 
users manual or not.  Water coming from beneath the machine.
Check the water intake and drain hoses. Tighten the con
-
nections. The washers of the hoses may be worn out. If 
non of the both, the pump filter is not closed properly.
Foam coming out of the detergent dispenser.
Check whether your detergent is suitable for automatic 
machines. Next time use less detergent.  
Pump does not drain water.
Clean the pump filter. Check whether the drain hose is
bent or not. If there is need to clean the pump filter, refer
to the pump filter cleaning section of the manual.
Descriptions of the international textile care label (ITCL) symbols
7
 
						

							
24