Beko Gne 134620 Instruction For Use

							EN10
C Adjust the door appropriately as you 
desire by loosing the screws.  
C Fix the door you have adjusted by 
tightening the screws without changing 
the position of the door.  
C Replace the hinge cover and fix with 
the screw.
  
						

							EN11
Installing Water Filter 
(in some models)
Two different water sources may 
be connected to the refrigerator for 
water supply: the mains cold water 
supply and water in a bottle.
Installation Requirements
A pump should be used for bottle water 
usage.
Check that the parts stated below are 
supplied with your appliance.
1. Union for connection of the water 
pipe to the rear of the appliance. (If it 
does not fit, provide it from the nearest 
authorized service.)
2.  2 pieces of pipe clips (In case required 
to secure the water pipe)
Note: Since the following parts are 
not required in use with a bottle, they 
may not be found in the product you 
purchased.
3.  5-meter long water pipe (1/4 inch in 
diameter)
4.  Cold mains water valve with mesh filter 
(Tap Adapter)
5.   Water Filter or externally connectable 
filter to be fitted to the bracket inside 
the fridge compartment.
Place where the external filter is going to 
be fitted should be determined first. 
(Applies to the filter being used outside 
the refrigerator.) Then, determine the 
distance between the filter and the 
refrigerator and required hose lengths 
from the filter to the refrigerator water 
inlet.
Water filter must be hold upright as shown 
in the figure. It is important to properly 
attach the filter to water inlet and water 
outlet points.
After attaching the filter, do not use first 3-4 
glasses of water.
Connection of the Water 
Pipe to the Refrigerator
1. After installing the union onto the 
water pipe, insert the water pipe to 
the refrigerator inlet valve by pressing 
downwards firmly.
2. Fix union as seen in the opposite 
figure, by squeezing by hand on the 
refrigerator inlet valve.
(a- Water Pipe, b-Union, c-Valve)
C Note 1: You should not need to 
tighten the union with a tool to achieve 
water tight assembly. In case of a leak 
use a spanner or a pair of pliers to 
tighten the union.
3
1 4
2 5
c
a
ab
1
2
  
						

							EN12
Connection of Water Hose to 
the Bottle 
(in some models)
To connect water to the refrigerator from 
a bottle, a pump is needed. Follow the 
instructions below after connecting one 
end of the water pipe coming out of the 
pump to the refrigerator as described on 
the previous page.
1. Finish the connection by pushing the 
other end of the water pipe into the 
water pipe inlet of the pump as shown 
in the figure.
2
1a
1b
2.  Put and fix the pump hose into the 
bottle as shown in the figure.
3.  After completing the connection, plug in 
and run the pump.
To provide an efficient operation of the 
pump, wait for 2-3 minutes after 
starting the pump.
C You may refer to the user manual 
of the pump while making the water 
connection.
C There is no need to use water filter in 
case a bottle is used.
C Pump must be used when bottle will be 
used.
  
						

							EN13
Connection of the Water 
Pipe to the Cold Water Mains 
Line 
(in some models)
If you want to use your refrigerator by 
connecting it to the cold water mains 
line, 
you will have to connect a standard 1/2" 
valve connection fitting to the cold water 
supply in your house. In case this valve is 
not present or in case you are not sure, 
consult a qualified plumber.
1. Separate the union from the tap 
adaptor. (Figure A) 
2.  Install the tap adaptor to 1/2” valve 
fitting as shown in the figure. (Figure B) 
3.  After inserting the water pipe to the 
union, install it to the tap adaptor and 
insert to the tap as shown in the figure.     
(Figure C) 
4.  Tighten the union manually. In case of a 
leak use a spanner or a pair of pliers to 
tighten the union. 
A Caution: Secure the water pipe 
to suitable points by means of the 
pipe clips supplied to avoid any 
damage or displacement or accidental 
disconnection.
A Caution: After turning on the water 
valve, make sure that there is no leakage 
at both connection points of the water 
pipe. In case of a leak, turn off the valve 
immediately and tighten all joints again 
using a spanner or a pair of pliers.
A Caution: Make sure that standard 
1/2" valve fitting fed by cold mains water 
supply is available and is turned off fully. 
To fit the water filter follow the 
instructions below referring to figures 
supplied:
1.  Press ice cancel button on the display.
  
						

							EN14
2. Remove the filter cover in the fridge 
compartment by pulling it forward.
3.  Take out the water filter by-pass cover 
by rotating it downwards. 
A Caution: Make sure that the “Ice off” 
mode is active before taking out the by-
pass cover. 
Note: It is normal that a few drops of 
water drip after the cover has been taken 
out.
4.  Remove the lid on top of the water filter 
to place it as shown in the figure and 
turn upwards to lock it.
5.  Press ice cancel button on the display 
again to exit from this mode.
Water filter should be replaced every 6 
months.
If you want to have the filter change time 
calculated automatically and receive a 
warning at the end of usage time, please 
read "Calculating the Filter Usage Time 
Automatically" section.
The water filter must be removed as 
  
						

							EN15
shown in the figure when it is going to 
be replaced or when it will no longer 
be used and by-pass cover must be 
attached. It must be made sure that Ice 
Off mode is active before taking it out.
A Caution: Water filter cleans some 
foreign particles in the water. It does not 
purify water from microorganisms.
A Caution: Ice Off button must always 
be pressed during replacement of the 
water filter or installing the by-pass 
cover.
Prior to first use of Water 
Dispenser
C Water mains pressure must not be 
below 100 kpa.
C Water mains pressure must not 800 
kpa.
C Pumps must be used in case the 
supply water pressure drops below 1 bar 
or if a bottle is going to be used.
C Water system of the refrigerator must 
be connected to the cold water line. It 
must not be connected to hot water line.
C No water may be obtained in the 
initial operation of the refrigerator. This 
is caused by the air in the system. To 
discharge air from the system, press 
Dispenser latch for periods of 1 minute 
until water comes from the Dispenser.  
Water flow may be irregular in the 
beginning. Irregular water flow will be 
normalized after the air in the system is 
discharged.
C At the initial startup of the refrigerator 
approx.12 hours must pass before cold 
water can be obtained.
C Water mains pressure must be 
between 100 - 800 kpa for the operation 
of Ice/Water Dispenser smoothly. For 
this, check that 1 glass of water (100 cc) 
can be filled in 10 seconds.
C The first 10 glasses of water should 
not be consumed.
C Approximately the first 30 cubes 
of ice to be obtained from the Ice 
Dispenser must not be used. 
C Always use the water filter when a 
bottle is not being used.
  
						

							EN16
4  Preparation
C Your refrigerator should be installed at 
least 30 cm away from heat sources 
such as hobs, ovens, central heater 
and stoves and at least 5 cm away 
from electrical ovens and should not be 
located under direct sunlight.
C The ambient temperature of the room 
where you install your refrigerator 
should at least be 10°C. Operating your 
refrigerator under cooler conditions 
than this is not recommended with 
regard to its efficiency.
C Please make sure that the interior of 
your refrigerator is cleaned thoroughly.
C If two refrigerators are to be installed 
side by side, there should be at least 2 
cm distance between them.
C When you operate your refrigerator 
for the first time, please observe the 
following instructions during the initial 
six hours.
  - The door should not be opened 
frequently.
 - It must be operated empty without 
any food in it.
 - Do not unplug your refrigerator. If 
a power failure occurs out of your 
control, please see the warnings in 
the “Recommended solutions for the 
problems” section.
C Original packaging and foam 
materials should be kept for future 
transportations or moving.
  
						

							EN17
5  Using your refrigerator
Indicator Panel
This touch-control indicator panel allows you to set the temperature without opening 
the door of your refrigerator. Just touch the relevant button with your finger to set the 
temperature. 
1. Eco-Extra / Vacation Button
2. Fast Freeze Button
3. Freezer Compartment Temperature 
Setting Button
4. Fridge Compartment Temperature 
Setting Button
5. Quick Cool Button
6. Multi Zone Compartment 
Temperature Setting Button
7. Vacation Function Indicator
8. Eco-Extra Function Indicator
9. Fast Freeze Function Indicator
10. Freezer Compartment Temperature 
Indicator
11. Fridge Compartment Temperature 
Indicator
12. Quick Cool Function Indicator
13. Multi Zone Compartment Temperature 
Indicator
14. Economy Mode Indicator
15. Error Status Indicator
16. Key Lock Indicator 
17. Ice Cancel Button
18. Ice Off indicator
19. Cancel Filter Change Warning Button
20. Filter Change Warning Indicator
 
1711 1215 4
5
6
2
3
1617 18
2019
109 14 1 38  
						

							EN18
1. Eco Extra/Vacation Button
Press this button briefly to activate the 
Eco Extra function. Press and hold this 
button for 3 sec. to activate the Vacation 
function. Press this button again to 
deactivate the selected function.
2. Fast Freeze Button
Press this button briefly to activate the 
Fast Freeze function. Press this button 
again to deactivate the selected function.
3. Freezer Compartment 
Temperature Setting Button
Press this button to set the temperature 
of the freezer compartment to -15 / -18 / 
-21 / -24  -15...  respectively. Press this 
button to set the desired temperature for 
the Freezer Compartment.
4. Fridge Compartment Temperature 
Setting Button
Press this button to set the temperature 
of the fridge compartment to 8, 6, 4, 2, 
8... respectively. Press this button to set 
the desired temperature for the Fridge 
Compartment.
5. Quick Cool Button
Press this button briefly to activate the 
Quick Cool function. Press this button 
again to deactivate the selected function.
6. Multi Zone Compartment 
Temperature Setting Button
You can set the Multi Zone 
Compartment either as a Freezer or a 
Cooler. Press and hold this button for a 
long time (3 sec) to set the Multi Zone 
Compartment as a Freezer or a Cooler. 
This compartment is set as a Freezer 
Compartment at factory. 
If the Multi Zone Compartment is set as 
a Freezer, then the temperature of the 
Multi Zone Compartment will change 
as -15, -18, -21, -24, -15... respectively 
each time you press this button. If the 
Multi Zone Compartment is set as a 
Fridge, then the temperature of the Multi 
Zone Compartment will change as 10, 8, 
6, 4, 2, 0, -6, ... respectively each time 
you press this button.
7. Vacation Function Indicator
Indicates that the vacation function 
is active. If this function is active, 
"- -" appears on the indicator of the 
fridge compartment and no cooling is 
performed in the fridge compartment. 
Other compartments will be cooled in 
accordance with the temperature set for 
them.
Press the relevant button again to 
deactivate this function.
8. Eco Extra Function Indicator
It indicates that the Eco-Extra function 
is active. If this function is active, your 
refrigerator will automatically detect 
the least usage periods and energy-
efficient cooling will be performed during 
those times. Economy indicator will be 
active while energy-efficient cooling is 
performed. 
Press the relevant button again to 
deactivate this function.
  
						

							EN19
9. Quick Freeze Function Indicator
It indicates that the Fast Freeze function 
is active. Use this function when 
you place fresh food into the freezer 
compartment or when you need ice. 
When this function is active, your 
refrigerator will run for a certain period of 
time.
Press the relevant button again to 
deactivate this function.
10. Freezer Compartment 
Temperature Indicator
It indicates the temperature set for 
Freezer Compartment.
11. Fridge Compartment 
Temperature Indicator
Indicates the temperature set for Fridge 
Compartment.
12. Quick Cool Function Indicator
Indicates that the Quick Cool function is 
active. Use this function when you place 
fresh food into the fridge compartment 
or when you need to cool your food 
quickly. When this function is active, your 
refrigerator will run for 2 hours without 
stopping.
Press the relevant button again to 
deactivate this function.
13. Multi Zone Compartment 
Temperature Indicator
It indicates the temperature set for Multi 
Zone compartment.
14. Economy Mode Indicator
Indicates that the refrigerator is running 
in energy-efficient mode. Freezer 
Compartment temperature 
This indicator will be active if the function 
is set to -15 or the energy efficient 
cooling is being performed due to Eco-
Extra function.
15. Error Status Indicator
If your refrigerator does not cool 
adequately or if there is a sensor failure, 
this indicator will be activated. When this 
indicator is active, Freezer Compartment 
Temperature indicator will display "E" 
and Fridge Compartment Temperature 
Indicator will display numbers such 
as "1,2,3…". These numbers on the 
indicator provides information about the 
error to the service personnel.
16. Key Lock Indicator
Use this function if you do not want your 
refrigerator temperature setting changed. 
Press Quick Cool Button and Flexi Zone 
Compartment Temperature Setting 
Button simultaneously for a long time (3 
sec) to activate this feature.
Press the relevant buttons again to 
deactivate this function.
17. Ice Cancel Button
To stop ice formation, ice cancel button 
is pressed for 3 seconds. When ice 
cancel is selected, no water will be sent 
to the ice box. Despite this, some ice 
may be leftover in the ice box which 
may be taken from there. To restart ice 
formation, ice cancel button has to be 
pressed for 3 seconds.