Baumatic Br11 2a Instruction Manual

 
  
10
 
ALWAYS Cover and wrap foods, especially if they are 
PUNGENT. 
• DO NOT place paper or plastic on the shelves which would 
block the flow of air through the grids. 
 
NOTE: At the maximum cold setting, with a high outside (ambient) 
temperature and well-stocked (full or nearly full) compartments, the 
Fridge’s operation may be continuous, leading to the formation of 
some frost on the evaporator.  
 
 
 
 
Should this happen, the knob must be turned to a less cold 
position to allow automatic...

 
  
11 
NOTE:  Before attempting to clean your appliance, UNPLUG IT and 
make sure you do the following: 
 
WE RECOMMEND THAT YOU CLEAN AND MAINTAIN YOUR 
REFRIGERATOR ONCE A MONTH. 
 
9 Pay particular attention to the sealing rubber bars of the doors.  These need to 
be kept clean for hygienic reasons as well as to allow the door to close 
properly. 
9 Leave the door open during cleaning. 
9 In order to collect the defrosted water, take out the bottom drawer and soak 
up the water using a sponge as...

 
  
12
Your appliance is equipped with a sound alarm which 
will sound to indicate that it is time to clear this dust 
from the condenser structure at the back of your 
appliance. 
 
• Disconnect the appliance from the power supply. 
• If the air opening in the bottom rail of the fridge 
is obstructed, remove the items responsible. 
• It dirty or dusty, you should clean or 
vacuum it (see the figure below). 
 
 
To remove Dust from the 
Condenser
 
1. Remove the 
bottom board of 
the unit cabinet. 
2....

 
  
13 
DEFROSTING 
 
Defrosting occurs fully automatically in the 
refrigerator compartment during normal operation.  
The defrosted water collected by the evaporating tray 
evaporates automatically. 
 
However, you will have to manually defrost the 
freezing compartment (icebox) when the frost 
and ice layer coating its interior is 3-5mm. 
 
You do this by: 
 
1) Turning the 
thermostat knob 
to the STOP (0) 
position and 
disconnecting the 
power supply. 
 
2) Emptying the 
icebox, taking care 
that...

 
  
14
TIPS FOR ENERGY SAVINGS 
 
9 Try not to open the door too often, especially when 
the weather is wet and hot.  Once you open the 
door, be sure to close it as soon as possible. 
 
9 Use higher thermostat settings only if essential 
and not for constant, long-term use. 
 
9 Before loading the appliance with packages of 
fresh foods, ensure they are cooled to an ambient 
temperature (except in the case of soup). 
 
9 Ice and frost layering will increase energy 
consumption, so defrost & clean the...

 
  
15 
 
1) Ensure that you are going to be 
placing your fridge away from heat 
sources and in a well-ventilated position.  
This should be at least 3 cm away from electric stoves and 30 cm from oil or 
coal stoves.  Do not place the appliance 
in the path of direct sunlight. 
 
 
2) After removing the rear wall of the cabinet, push the appliance into the 
kitchen unit’s space and allow at least 4mm free space on both sides between 
the appliance and the side walls of the kitchen unit (Fig.1, at...

 
  
16
INSTALLING YOUR APPLIANCE- CONTINUED 
 
Fitting Bar
 
 
 
 
 
 
 
 
 
  
*Please be aware that the Fitting Bar is not attached to 
the appliance and needs to be secured during 
installation. 
Install the Fitting Bar (shown in the picture below), so 
that it attaches to the top of the appliance and 
underneath the top of the cabinetry, indicated by the 
arrow: 
 

 
  
17 
 
 
YOU MUST install this appliance in well ventilated, dry 
room.  
Energy use is affected by the ambient temperature. 
 
 You are therefore advised to: 
ƒ Not expose the appliance to direct sunlight; 
 
ƒ Not  install the appliance next to radiators, 
cookers or other sources of heat; 
 
ƒ Only install the appliance at a location whose 
ambient temperature corresponds to the climate 
classification, for which the appliance is designed. 
 
The climate classification can be found on the data...

 
  
18
Fitting the Décor Door 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2)  Fix the hanging 
rail onto the inside 
of the décor door 
using two 10mm 
screws, centering it 
so that  262mm of 
its width is on either 
side of the 
imaginary vertical 
middle line of the 
décor door.   
 
 
1) Using a 2.8mm 
diameter bit, make 
holes sufficient to 
attach the rail as 
shown on the left. 
NOTE – door area 
below the rail 
must reach to just 
below appliance. 
NOTE: 
You need 
the tools 
shown...

 
  
19 
Adjusting the feet to level your Appliance 
Adjust the feet (see picture at 
right) until your Fridge sits levelly 
on your floor.  You can level your 
unit using these adjustable feet to 
compensate for dips and rises in 
your floor surface.   
 
NOTE: You can adjust the height 
from 82 to 90 cm.  The height 
MUST be adjusted before
 the 
appliance is built into the unit
 
space designated for it.  
 
 
 
DO NOT MOVE THE FRIDGE WHEN THE FEET ARE EXTENDED HIGH! 
 
 
 
  
 
Drill two holes 
and...