Avio Ip-30 Intelligent Projector Users Manual

E-1

Maintenance
The projector is equipped with a built-in protection circuit to prevent fire and breakdown due to faults.
When the LAMP/COVER LED lights in red
 Measures to be taken
1. Disconnect the power plug from the outlet.
2. Properly install the lamp unit cover. See "Replacement of the Lamp Unit" on Page E-43.
When the TEMP LED flashes or lights steadily
 Measures to be taken
1. Disconnect the power plug from the outlet.
2. Check the following matters and perform the countermeasure...

E-

When the power has failed (When all the LED go off with the power ON)
 Measures to be taken
1. Disconnect the power plug from the outlet.
2. Check the following matters and perform the countermeasure properly.
Maintenance
Is  the  ambient  temperature 
in excess of 35°C (95°F)?
A r e  t h e  v e n t i l a t i o n  v e n t s 
blocked?
B r e a k d o w n  o f  a n  i n t e r n a l 
circuit could be the problem.
Please  use  the  projector  in  an  operation  ambient  tempera-
ture of 0°C...

E-

Replacement of the Lamp Unit
The  projection  lamp  used  on  this  projector  should  be  replaced  after  about  the  number  of  hours  indicated  below  (or  sooner,  de-
pending on the usage conditions).
When the usage time exceeds 2000 hours*, the possibility for explosion increases, so the lamp is forcibly shut off.
When the usage time exceeds 1900 hou rs, replace the lamp unit (sold separately) before the usage time reaches 2000 hours.  
Also, if the picture is dark, the lamp has...

E-

Maintenance
ÀÝ




1Remove the lamp unit cover
Using  a  minus  screwdriver,  loosen  the  screws  of  the 
lamp  unit  cover,  pull  in  the  direction  of  the  arrow,  and 
remove the cover.
2Loosen the mounting screws of the lamp unit
Using  a  minus  screwdriver,  loosen  the  2  screws  of 
the lamp unit.
3Pull out the lamp unit
Hold the handle of the lamp unit and pull it up and out.
4Install a new lamp unit
❶ Take the lamp unit and press it into the projector.
❷ Check that...

E-

Maintenance
5Reset the lamp usage time
Please perform the operation indicated below in the standby mode (*).
6Check  that  the  indication  of  the  lamp  us-
age  time  has  become  "0  H"  as  illustrated 
in the diagram to the right.
If  the  usage  time  has  not  been  reset,  please  reset  it 
by following Step 5 again.
Check  the  lamp  usage  time  by  pressing  the  menu  button  of 
the  remote  control  to  display  the  menu,  then  use  the  scroll 
◀▶ button to...

E-

Maintenance
1Pull out the air filter A.
Air Filter Cleaning Procedure
Cleaning the Air Filter
The  air  filter  is  an  important  part  that  prevents  the  intrusion  of  dust  onto  the  optical  parts  and  other  parts  inside 
the projector. When the air filter becomes blocked, the internal temperature will rise and the rotation of the fan will 
also increase leading to a reduction of the service life or causing breakdown. In view of this, the air filter should be 
cleaned regularly...

E-

Troubleshooting
When you think the projector may be out of order, please first check the following matters before requesting repair.
SymptomPlease check thisReference page
Power does not come on• Is the power cable connected?E-21
Projection  lamp  does  not 
light
• Is the lamp burned out?
• Is the lamp unit cover installed?
• Is the internal temperature high? If so, the lamp will not light to protect 
the projector from damage.
• Is the lamp usage time in excess of 2000 hours?
E-43
E-44...

E-

Repair Service Procedure
• Before  asking  for  repair  service,  check  the  Troubleshooting  section  on  page  E-47  once  more.  If  this  check  confirms  a  prob-
lem, contact the dealer where you bought the product.
• When asking for repair service, provide your dealer with the following information:
Description of the problem (as many details as possible)
Date of purchase
Your Name
Your Address
Telephone number
Product name and model No. (written on the label at the bottom of the...

E-

Specifications
*1 USB connectors are not guaranteed to work with all personal computers.
*2 No USB cable is included with the iP-30BE’s PC connection cable.
  The “iP Viewer Software Quick Reference” is not included with the iP-30BE.
• Specifications and designs are subject to change without prior notice in order to improve the product.
The specifications are subject to change without notice.
Model NameiP-30SE/iP-30BE
TypeSingle-plate DLP ® color wheel color separation type
Main Part...