ATT Dect 6.0 User Manual
Here you can view all the pages of manual ATT Dect 6.0 User Manual. The ATT manuals for Corded Headset are available online for free. You can easily download all the documents as PDF.
Page 31
24 Getting started Headset base and handset lifter installation Adjust the height of the lifter arm Turn the ADJUST LIFTER knob to change the height of the lifter arm. When in the raised position, the arm should release the switch hook so you can hear a dial tone. When lowered, the arm should hold the switch hook down so you cannot hear a dial tone. Adjust the switch hook presser position Turn the knob to move the switch hook presser until it is lined up with your telephone switch hook.
Page 32
25 Getting started Headset base and handset lifter installation Lifter adjustments and testing 1. Make sure that the CORDED HANDSET CONNECTED switch on the headset base is set to YES. 2. Turn the switch hook presser adjustment knob until the switch hook presser is just above the switch hook (see page 24). 3. Lower the lifter arm until the switch hook presser holds the switch hook down. 4. Place the corded handset on the lifter. 5. Press on the headset. The switch hook presser should rise and...
Page 33
26 Getting started Headset base and handset lifter installation Installation of large lifter pad (optional) If the small lifter pad cannot hold the corded handset steadily, you can attach a large lifter pad (provided) to enlarge the contact area. 1. Hold the large lifter pad in front of the small lifter pad, as shown below. 2. Insert the large lifter pad into the two front gaps of the small lifter pad. Installation of anti-slip pad (optional) The anti-slip pad (provided) helps prevent your corded...
Page 34
27 Getting started Install the auxiliary ring detector 1. Insert the auxiliary ring detector plug into the RING DETECT jack on the lifter. 2. Remove the protective strip from the adhesive tape on the auxiliary ring detector. 3. Stick the auxiliary ring detector to the center of the corded phone speaker. The internal or auxiliary ring detector detects the telephone ringer and sends a ring tone to the headset earpiece. If you installed the lifter over the top of the corded phone speaker, the...
Page 35
28 Getting started About internal and auxiliary ring detectors Adjust the sensitivity level The default setting of the ring detector works with most corded telephones. However, the ring detector might need some adjustments if the ring tone level of your corded phone is too soft. To adjust the ring detector sensitivity while the telephone is ringing: Turn the SENSOR ADJ knob clockwise to increase the sensitivity. Turn the SENSOR ADJ knob counterclockwise to decrease the sensitivity. When the...
Page 36
29 Getting started Headset attachments Earbud There are a total of six earbuds provided. One of them has been attached to the headset. They come in three sizes of which there are two types: one normal and one providing a deeper fit. Follow the steps to change the earbud. To remove the earbud from the headset earpiece: Hold both sides of the earbud. Twist and pull the earbud until it separates from the earpiece. To attach the earbud to the headset earpiece: Choose an appropriate earbud. Position the...
Page 37
30 Getting started To wear on the left ear:• To wear on the right ear:• Figure 1 Figure 2 Headset attachments Over the ear hook There are three ear hooks provided. Choose the size that best fits your need to attach to the headset. Follow the steps to attach an ear hook to the headset. To position the headset to wear on the left or right ear: Make sure the ear hook loop is positioned, as shown in Figure 1 on the right. Attach the ear hook to the headset, as instructed on the next page. 1. 2. Make...
Page 38
31 Getting started Headset attachments To attach the ear hook to the headset: Make sure there is no headset attachment, except the earbud, connected to the headset. Insert the earpiece into the ear hook loop, as shown in Figure 3. Press the edge of the ear hook loop towards the earpiece until it clicks into place, as shown in Figure 4. 4. Hook the headset onto the desired ear. Adjust the angle of the headset until the microphone is pointing towards your mouth, as shown in Figure 5. 1. 2. 3. Figure...
Page 39
32 Getting started Headset attachments To remove the ear hook from the headset: Hold the headset with one hand. Twist and pull the ear hook with the other hand until it separates from the earpiece.
Page 40
33 Getting started Headset attachments Over the head band There are two over the head bands provided. Choose the one that best fits your need to attach to the headset. Follow the steps to attach an over the head band to the headset. To attach the head band to the headset: Make sure there is no headset attachment, except the earbud, connected to the headset. Insert the earpiece into the loop of the ear pad, as shown in Figure 6. Push the earpiece into the ear pad until it clicks into place, as...
All ATT manuals