ATT 3800hgvb Manual

							
Access the Management and Diagnostic Console
39
Network Name The default setting is the word “2WIRE,” followed by the last three digits of the 2Wire gateway serial number.
Authentication The authentication method used: Open, Shared, or WPA- PSK (Wi-Fi Protected Access pre-shared key).
Encr yption The encr yption method used: WEP or TKIP . 
Channel The frequency channel in use. The default channel is 6. If  multiple access devices within the vicinity use the same 
channel, you can set a different channel to eliminate poten-
tial interference.
Devices (the information displayed is  dependent on the gateway model features)
Ethernet The number of Active and Inactive Ethernet devices on the  network.
Wireless (802.11) The number of Active and Inactive wireless devices on the  network.
HomePNA The number of Active and Inactive HomePNA devices on  the network.
USB Specifies whether a USB device  is present (Active) on the 
network. If a USB device is not present, the value is 
Inactive.
MoCA The number of Active and Inactive MoCA devices on the  network.
Public Network
Router Address Defines a s eparate network on the home side.
Subnet Mask The subnet mask allocated for public address. Item Description 
						

							
Access the Management and Diagnostic Console
40
Local Network - Statistics Page
Note: The information displayed is dependent on gateway model features.
The Local Network – Statistics page shows inform ation about the interfaces on the local network. 
						

							
Access the Management and Diagnostic Console
41
Local Network - Device List Page
The Local Network - Device List page displays information about each device in the local network. 
						

							
Access the Management and Diagnostic Console
42
Local Network - Wireless Settings Page
The Wireless Settings page allows you to view or modify the gateway’s wireless settings.
For details on configuring wireless settings, refer to page 23. 
						

							
Access the Management and Diagnostic Console
43
Local Network - Configuration Page
The Local Network - Configuration page allows you to change the gateway’s default local network settings. 
You must click the 
Submit button for changes to take effect.
For details on configuring advanced network settings, refer to page 24.
Enabling Router Behind Router Aler t
When the Display alert when another router is connected to this router checkbox is enabled, an error page is 
displayed to the user if the gateway detects the pres ence of a third-par ty router on the user’s network. A 
third-party router connected to the 2Wire gateway can re sult in network instability, because both devices are 
tr ying to manage private IPs via NAT. 
						

							
Access the Management and Diagnostic Console
44
Local Network - Address Allocation Page
The Local Network - Address Allocation page shows the name and IP address of each device on the 
gateway’s local network, and allows you to create DHCP mappings for each device.
For details on network address allocation, refer to  “Editing Address Allocation Settings” on page 25. 
						

							
Access the Management and Diagnostic Console
45
Local Network - Configure the MoCA Network Page
The Configure the MoCA Network page allows you to change the channel upon which the MoCA signal is 
sent or received, enable or disable network privac y, and set the password for network privacy. These 
settings are only used when the gateway is connect ed via MoCA. When MoCA is used through external 
devices, these settings are not applicable. 
						

							
Access the Management and Diagnostic Console
46
Local Network - MoCA Statistics Page
The MoCA Statistics page shows connection rates to other MoCA devices. 
 If the 3700HGV-B is the coordinator, the link rate to the slaves.
 If the 3700HGV-B is not the coordinator , the link rate to the coordinator. 
						

							
Access the Management and Diagnostic Console
47
Firewall - Settings Page
The Firewall - Settings page allows you to configure the firewall to pass through specific application data to 
a selected computer.
For details on configuring the firewall, refer to page 28. 
						

							
Access the Management and Diagnostic Console
48
Firewall - Detailed Information Page
The Firewall - Detailed Information page shows detailed information about the gateway’s firewall.