Asus Zen AiO Z220IC Z240IC User Manual

							41
or
1. Launch Settings from the Start menu.
2. Select  Devices, then select Bluetooth to search for 
Bluetooth-enabled devices.
3.  Select a device from the list. Compare the passcode 
on your ASUS All-in-One PC with the passcode sent 
to your chosen device. If they are the same, select 
Yes to successfully pair your ASUS All-in-One PC 
with the device.
NOTE: For some bluetooth-enabled devices, you may be 
prompted to key in the passcode of your ASUS All-in-One 
PC.
Bluetooth 
Use Bluetooth to facilitate wireless data transfers with other Bluetooth-
enabled devices.
Pairing with other Bluetooth-enabled devices
You need to pair your ASUS All-in-One PC with other Bluetooth-enabled 
devices to enable data transfers. Connect your devices by using the 
following steps:
ASUS All-in-One PC   
						

							42
Connecting to wired networks
You can also connect to wired networks, such as local area networks 
and broadband Internet connection, using your ASUS All-in-One PC’s 
LAN port.
NOTE: Contact your Internet Service Provider (ISP) for details or 
your network administrator for assistance in setting up your Internet 
connection.
To configure your settings, refer to the following procedures.
IMPORTANT! Ensure that a network cable is connected between your 
ASUS All-in-One PC’s LAN port and a local area network before performing 
the following actions.
Configuring a dynamic IP/PPPoE network 
connection
or
1. Launch Settings.
2. Select  Network & Internet.
3. Select  Ethernet > Network and Sharing Center.
4.  Select your LAN then select Properties.
5. Select  Internet Protocol Version 4(TCP/IPv4) then 
select Properties.
6. Select  Obtain an IP address automatically then 
select OK.
NOTE: Proceed to the next steps if you are using PPPoE connection.
ASUS All-in-One PC  
						

							43
7. Return to the Network and Sharing Center 
window then select Set up a new connection or 
network.
8. Select  Connect to the Internet then select Next .
9. Select  Broadband (PPPoE).
10.  Type your User name, Password, and Connection 
name then select Connect.
11. Select  Close to finish the configuration.
12. Select 
 on the taskbar then select the 
connection you just created.
13.  Type your user name and password then select 
Connect to start connecting to the Internet.
Configuring a static IP network connection
or
1. Repeat steps 1 to 5 under Configuring a dynamic 
IP/PPPoE network connection.
2. Select  Use the following IP address.
3.  Type the IP address, Subnet mask and Default 
gateway from your service provider.
4.  If needed, you can also type the preferred DNS 
server address and alternate DNS server address 
then select  OK.
ASUS All-in-One PC   
						

							44
Turning your ASUS All-in-One PC 
off
You can turn off your ASUS All-in-One PC by doing either of the 
following procedures:
or
•	 Launch	the	Start	menu,	then	select	 > 
Shut down to do a normal shutdown.
•	 From	the	log-in	screen,	select	
 > Shut down.
•	 Press	 to launch Shut Down 
Windows. Select Shut Down from the drop-
down list then select OK.
•	 If	your	ASUS	All-in-One	PC	is	unresponsive,	press	 and hold the power button for at least four (4) 
seconds until your ASUS All-in-One PC turns off.
ASUS All-in-One PC  
						

							45
Putting your ASUS All-in-One PC to sleep
To put your ASUS All-in-One PC to Sleep mode: 
or
•	 Launch	the	Start	menu,	then	select	 > 
Sleep to put your ASUS All-in-One PC to sleep.
•	 From	the	log-in	screen,	select	
 > Sleep.
Press  to launch Shut Down Windows. 
Select Sleep from the drop-down list then select OK.
NOTE: You can also put your ASUS All-in-One PC to Sleep mode by 
pressing the power button once.
ASUS All-in-One PC   
						

							46
ASUS All-in-One PC  
						

							Chapter 4: Recovering your 
system
Entering the BIOS Setup
BIOS (Basic Input and Output System) stores system hardware settings 
that are needed for system startup in the ASUS All-in-One PC. 
In normal circumstances, the default BIOS settings apply to most 
conditions to ensure optimal performance. Do not change the default 
BIOS settings except in the following circumstances: 
•	 An	error	message	appears	on	the	screen	during	the	system	bootup and requests you to run the BIOS Setup.
•	 You	have	installed	a	new	system	component	that	requires	further	 BIOS settings or update.
WARNING! Inappropriate BIOS settings may result to instability or boot 
failure. We strongly recommend that you change the BIOS settings only 
with the help of a trained service personnel.
Quickly enter the BIOS
To access the BIOS:
•	 When	your	ASUS	All-in-One	PC	is	off,	press	the	power	button	for	at least four (4) seconds to access the BIOS directly.
•	 Press	the	power	button	to	turn	on	your	ASUS	All-in-One	PC	then	 press  or  during POST.
NOTE: POST (Power-On Self-Test) is a series of software controlled 
diagnostic tests that run when you turn on your ASUS All-in-One PC.
47
ASUS All-in-One PC   
						

							Recovering your system
Using recovery options on your ASUS All-in-One PC allows you to 
restore the system to its original state or simply refresh its settings to 
help improve performance.
IMPORTANT! 
•	Backup all your data files before doing any recovery option on your 
ASUS All-in-One PC.
•	 Note	down	important	customized	settings	such	as	network	settings,	 user names, and passwords to avoid data loss.
•	 Ensure that your ASUS All-in-One PC is plugged in to a power source  before resetting your system.
Windows® 10 allows you to do any of the following recovery options:
•	 Keep	my	files	- This option allows you refresh your ASUS All-in- One PC without affecting personal files (photos, music, videos, 
documents).
  Using this option, you can restore your ASUS All-in-One PC to its 
default settings and delete other installed apps.
•	 Remove	everything	- This option resets your ASUS All-in-One PC  to its factory settings. You must backup your data before doing 
this option.
48
ASUS All-in-One PC  
						

							•	 Go	back	to	an	earlier	build	- This option allows you to go back to an earlier build. Use this option if this build is not working for 
you.
•	 Advanced	startup	- Using this option allows you to perform  other advanced recovery options on your ASUS All-in-One PC 
such as:
-    Using a USB drive, network connection or Windows recovery 
DVD to startup your ASUS All-in-One PC.
- Using  Troubleshoot to enable any of these advanced 
recovery options: System Restore, System Image Recovery, 
Startup Repair, Command Prompt, UEFI Firmware Settings, 
and Startup Settings.
Performing a recovery option
Refer to the following steps if you want to access and use any of the 
available recovery options for your ASUS All-in-One PC.
1. Launch  Settings and select Update and security.
49
ASUS All-in-One PC   
						

							2. Under the Update and security option, select Recovery then 
select the recovery option you would like to perform.
50
ASUS All-in-One PC