Asus Vw202b User Guide

							
1-3ASUS VW202xR/VW202B LCD Monitor

1.3.2 Back view
5.  Power button/power indicator          
 • Press this button to turn the monitor on/off
  • The color definition of the power indicator is as the below table.
1. Audio-in port. This port connects PC audio source by the bundled audio 
cable.
2. AC-IN port. This port connects the power connector from the bundled power 
cord.
3. DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal 
connection.
  USB port (VW202B only). This port is for the built-in USB hub and ASUS 
EzLink Display connection.
4. VGA port. This 15-pin port is for PC VGA connection. 
Rear connectors 
StatusDescription
  BlueON
  AmberStandby mode
  OFFOFF
Stereo speaker
Rear connectors
Stereo speakerScrew holes for VESA Wall Mount
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.
1234234
VW202BVW202xR / VW202B 
 
						

							
1-4Chapter 1: Product introduction
 
						

							
2-1ASUS VW202xR/VW202B LCD Monitor
2.1 Assembling the monitor base
To assemble the monitor base:
1. Have the front of the monitor face down on a table.
2. Connect the base with the arm according to the below drawing. A click shows 
that the base has been connected successfully. 
We recommend that you cover the table surface with soft cloth to prevent \
damage to the monitor. 
2.2  Adjusting the monitor
• For optimal viewing, we recommend that you look at the full face of the 
monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
• You can adjust the monitor’s angle from -3º to 20º.
It is normal that the monitor slightly shakes while you adjust the the v\
iewing angle. 
 -3º~20º
 
						

							
2-2Chapter 2: Setup

2.3 Detaching the arm/base  
 (for VESA wall mount)
The detachable arm/base of the VW202xR/VW202B LCD monitor is specially 
designed for VESA wall mount. 
To detach the arm/base: 
1. Have the front of the monitor face down on a table.
2. Remove the rubbers in the four screw holes (Figure 1).
3. Use a screwdriver to remove the two screws on the arm (Figure 1), then slide 
out the arm/base to detach it from the monitor (Figure 2).
We recommend that you cover the table surface with soft cloth to prevent \
damage to the monitor.
Arm/base
Rubbers in the screw holes 
Two screws 
Figure 1Figure 2
 
						

							
2-3ASUS VW202xR/VW202B LCD Monitor

2.4 Connecting the cables
1. Connect the cables as the following instructions:
• To connect the power cord: connect one end of the power cord securely to 
the monitor’s AC input port, the other end to a power outlet.
• To connect the USB cable (VW202B only): connect the B-type end of the 
USB cable to the monitor's USB port, and the A-type end to the computer's 
USB 2.0 port. 
• To connect the VGA cable / DVI cable: 
a. Plug the VGA / DVI connector to the LCD monitor’s VGA / DVI port.
b. Connect the other end of the VGA / DVI cable to your computer’s VGA / 
DVI port.
c. Tighten the two screws to secure the VGA / DVI connector.
2.5  Turning on the monitor
Gently press the power button  . See page 1-2 for the location of the power 
button. The power indicator  lights up in blue to show that the monitor is ON.
When both the VGA and the DVI cables are connected, you can choose either 
VGA mode or DVI mode from the Input Select item of the OSD functions.
• To connect the audio cable: connect one end of the audio cable to the  
monitor’s Audio-in port, the other end to the computer's audio-out port. 
2. Gather all the cables with the cable hook.
Cable hook
(B-Type)2.0
VW202BVW202xR/VW222B
 
						

							
2-4Chapter 2: Setup
 
						

							
3-1ASUS VW202xR/VW202B LCD Monitor
3.1 OSD (On-Screen Display) menu 
3.1.1  How to reconfigure
1. Press the MENU button to activate  
the OSD menu. 
                    
           
2. Press  and  to navigate through the functions. Highlight and activate 
the desired function by pressing the MENU button. If the function select\
ed 
has a sub-menu, press  and  again to navigate through the sub-menu 
functions. Highlight and activate the desired sub-menu function by press\
ing 
the MENU button.  
3. Press  and  to change the settings of the selected function.
4. To exit the OSD menu, press the  button. Repeat step 2 and step 3 to 
adjust any other function.  
3.1.2  OSD Function Introduction
1. Spendid
 This function contains five  
sub-functions you can select  
for your preference. Each mode has the 
Reset selection, allowing you to maintain 
your setting or return to the preset mode.
 • Scenery Mode: best choice for scenery photo display with SPLENDID™   
 Video Enhancement.
 •   Standard Mode: best choice for document editing with SPLENDID™   
  Video Enhancement.
 •   Theater Mode: best choice for movie with SPLENDID™ Video    
  Enhancement.
 •   Game Mode: best choice for game playing with SPLENDID™ Video 
  Enhancement.
 •   Night View Mode: best choice for dark-scene game or movie with  
  SPLENDID™ Video Enhancement. 
• In the Standard Mode, the Satuation and Sharpness functions are not user-configurable.
• In the other modes, the sRGB function is not user-configurable.
 
						

							
3-2Chapter 3: General Instruction  

• Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows  horizontal disturbances.
• Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vert\
ical stripes and the image is not proportional.
3.  Color  
 Select the image color you like 
 from this function. 
 
 • Color Temp.: contains five color modes including Cool, Normal,    
  Warm, sRGB, and User mode.      
 • Skin Tone: contains three color modes including Reddish, Natural,    
  and Yellowish. 
In the User mode, colors of R (Red), G (Green), and B (Bluee) are \
 user-configurable; the adjusting range is from 0-100.
2. Image 
 You can adjust brightness, contrast,  
sharpness, saturation,position (VGA  
only), ASCR, and focus (VGA only) from  
this main function. 
 • Brightness: the adjusting range is from 0 to 100.  is a hotkey to    
  activate this function.
 • Contrast: the adjusting range is from 0 to 100.
 • ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.
 • Sharpness: the adjusting range is from 0 to 100.
 • Saturation: the adjusting range is from 0 to 100. 
 • Position: adjusts the horizontal postition (H-Position) and the vertical   
  position (V-Position) of the image. The adjusting range is from 0 to 100.
 • Focus: reduces Horizonal-line noise and Vertical-line noise of the image  
  by adjusting (Phase) and (Clock) separately. The adjusting range is from  
 0 to 100.
 
						

							
3-3ASUS VW202xR/VW202B LCD Monitor

4. Input Select 
 In this function, you can select  
either VGA, DVI, or EzLink (VW202B 
only) input source.
5. System Setup 
 Allow you to adjust the system.
 • Volume: the adjusting range is from 0 to 100.  is a hotkey to activate  
  this function. 
 • OSD Setup: 
    *���Adjusts the horizontal postition (H-Position)/ the vertical position   Adjusts the horizontal postition (H-Position)/ the vertical positionAdjusts the horizontal postition (H-Position)/ the vertical position    
       (V-Position) of the OSD from 0 to 100. 
    *���   Adjusts the OSD timeout from 10 to 120. 
    *���   Enables or disables the DDC/CI function.   
 • Language: there are ten languages for your selection, including English,   
 German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,  
 Simplified Chinese, and Japanese. 
 • Aspect Control: adjusts the aspect ratio to “Full” or “4:3”. 
 • Information: shows the monitor information. 
 • Reset: “Yes” allows you to restore the default setting. 
 
						

							
3-4Chapter 3: General Instruction  

3.2 ASUS EzLink Display (VW202B only)
ASUS EzLink Display allows you to transfer digital video signal from you\
r PC 
to your LCD via a standard USB 2.0 cable. Without the necessity of purch\
asing 
additional graphics cards, EzLink Display provides the flexibility for m\
ulti-screen 
applications.
3.2.1 System requirements
Before you install the ASUS EzLink Display software, check if your system meets 
the following requirements:
Hardware:
• PC with 1.2 GHz or higher
• 512MB of RAM or higher
• USB 2.0 port
• 30MB of available disk space
• Super VGA (800 x 600) video adaptor or higher resolution
• USB cable A-type to B-type
Supporting operating system:
• Windows 2000 SP4
• Windows XP SP2/SP3
• Windows Vista