Asus Vw195u User Guide

							
1-3ASUS VW195 Series LCD Monitor 

1.3.2	 Back	view
5.  Power button/power indicator          
 • Press this button to turn the monitor on/off
  • The color definition of the power indicator is as the below table.
1. Audio-in	port. This port connects PC audio source by the bundled audio 
cable. (VW195U / VW195T / VW195S only)
. AC-IN	port. This port connects the power connector from the bundled power 
cord.
3. DVI	port. This 4-pin port is for PC (Personal Computer) DVI-D digital signal 
connection. (VW195U / VW195T only)
4. VGA 	port. This 15-pin port is for PC VGA connection. 
Rear	connectors	
StatusDescription
  BlueON
  AmberStandby mode
  OFFOFF
Stereo	speaker
Rear	connectors
Stereo	speakerScrew	holes	for	VESA 	Wall	Mount
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.
1234
Downloaded	from	ManualMonitor.com	Manuals 
						

							
1-4Chapter 1: Product introduction
 
						

							
-1ASUS VW195 Series LCD Monitor 
2.1	 Assembling	the	monitor	base
To assemble the monitor base:
1. Have the front of the monitor face down on a table.
. Connect the base with the arm according to the below drawing. A click shows 
that the base has been connected successfully. 
We  recommend  that  you  cover  the  table  surface  with  soft  cloth  to  prevent damage to the monitor. 
2.2	 Adjusting	the	monitor
• For optimal viewing, we recommend that you look at the full face of the 
monitor, then adjust the monitor to the angle that is most comfortable for you.
• Hold the stand to prevent the monitor from falling when you change its angle.
•	 You	can	adjust	the	monitor’s	angle	from	-5˚	to	20˚.
It is normal that the monitor slightly shakes while you adjust the the v\
iewing angle. 
	-5˚�20˚˚�20˚�20˚˚
 
						

							
-Chapter : Setup

2.3	 Detaching	the	arm/base		
	 (for	VESA	wall	mount)
The detachable arm/base of the VW195 Series LCD monitor is specially designed 
for VESA wall mount. 
To detach the arm/base: 
1. Have the front of the monitor face down on a table.
. Remove the rubbers in the four screw holes (Figure 1).
3. Use a screwdriver to remove the two screws on the arm (Figure 1), then slide 
out the arm/base to detach it from the monitor (Figure ).
We recommend that you cover the table surface with soft cloth to prevent \
damage to the monitor.
Arm/base
Rubbers	in	the	screw	holes	
Two	screws	
Figure	1Figure	2
Downloaded	from	ManualMonitor.com	Manuals 
						

							
-3ASUS VW195 Series LCD Monitor 

2.4	 Connecting	the	cables
1. Connect the cables as the following instructions:
• To	connect	the	audio	cable: connect one end of the audio cable to the  
monitor’s Audio-in port, the other end to the computer's audio-out port. 
• To	connect	the	power	cord: connect one end of the power cord securely to 
the monitor’s AC input port, the other end to a power outlet.
• To	connect	the	VGA/DVI	cable: 
 a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.  
b. Connect the other end of the VGA/ DVI cable to your computer’s VGA/ 
 DVI port. 
c. Tighten the two screws to secure the VGA/DVI connector.
2.5	 Turning	on	the	monitor
Gently press the power button  . See page 1- for the location of the power 
button. The power indicator  lights up in blue to show that the monitor is ON.
When  both  the  VGA  and  the  DVI  cables  are  connected,  you  can  choose  either VGA mode or DVI mode from the Input Select item of the OSD functions.
.  Gather all the cables with the cable hook.
Cable	hook
Downloaded	from	ManualMonitor.com	Manuals 
						

							
-4Chapter : Setup
 
						

							
3-ASUS VW95 Series LCD Monitor 
3.1	 OSD	(On-Screen	Display)	menu	
3.1.1	 How	to	reconfigure
. Press the MENU button to activate  
the OSD menu. 
                    
           
2. Press  and  to navigate through the functions. Highlight and activate 
the desired function by pressing the MENU button. If the function select\
ed 
has a sub-menu, press  and  again to navigate through the sub-menu 
functions. Highlight and activate the desired sub-menu function by press\
ing 
the MENU button.  
3. Press  and  to change the settings of the selected function.
4. To exit the OSD menu, press the  button. Repeat step 2 and step 3 to 
adjust any other function.  
3.1.2	 OSD	Function	Introduction
1.	 Spendid
 This function contains five  
sub-functions you can select  
for your preference. Each mode has the 
Reset selection, allowing you to maintain 
your setting or return to the preset mode.
 • Scenery	Mode: best choice for scenery photo display with SPLENDID™   
 Video Enhancement.
 •   Standard	Mode: best choice for document editing with SPLENDID™   
  Video Enhancement.
 •   Theater	Mode: best choice for movie with SPLENDID™ Video    
  Enhancement.
 •   Game	Mode: best choice for game playing with SPLENDID™ Video 
  Enhancement.
 •   Night	View	Mode: best choice for dark-scene game or movie with  
  SPLENDID™ Video Enhancement. 
• In the Standard Mode, the Saturation and Sharpness functions are not user-configurable.
• In the other modes, the sRGB function is not user-configurable.
 
						

							
3-2Chapter 3: General Instruction  

• Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows  horizontal disturbances.
• Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vert\
ical stripes and the image is not proportional.
3.	 Color		
  Select the image color you like 
 from this function. 
 
 • Color	Temp.: contains five color modes including Cool, Normal,    
  Warm, sRGB, and User mode.      
 • Skin	Tone: contains three color modes including Reddish, Natural,    
  and Yellowish. 
In the User mode, colors of R (Red), G (Green), and B (Bluee) are \
user-configurable; the adjusting range is from 0-00.
2.	 Image	
 You can adjust brightness, contrast,  
sharpness, saturation,position (VGA  
only), ASCR, and focus (VGA only) from  
this main function. 
 • Brightness: the adjusting range is from 0 to 00.  is a hotkey to    
  activate this function.
 • Contrast: the adjusting range is from 0 to 00.
 • ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.
 • Sharpness: the adjusting range is from 0 to 00.
 • Saturation: the adjusting range is from 0 to 00. 
 • Position: adjusts the horizontal postition (H-Position) and the vertical   
  position (V-Position) of the image. The adjusting range is from 0 to 00.
 • Focus: reduces Horizonal-line noise and Vertical-line noise of the image  
  by adjusting (Phase) and (Clock) separately. The adjusting range is from  
 0 to 00.
 
						

							
3-3ASUS VW95 Series LCD Monitor 

4.	 Input	Select	
 In this function, you can select  
either VGA or DVI input source. 
(Only for some models)
5.	 System	Setup	
 Allow you to adjust the system.
 • Volume: the adjusting range is from 0 to 00.  is a hotkey to activate  
  this function. 
 • OSD	Setup: 
    *���Adjusts the horizontal postition (H-Position)/ the vertical position   Adjusts the horizontal postition (H-Position)/ the vertical positionAdjusts the horizontal postition (H-Position)/ the vertical position    
       (V-Position) of the OSD from 0 to 00. 
    *���   Adjusts the OSD timeout from 0 to 20. 
    *���   Enables or disables the DDC/CI function.   
 • Language: there are ten languages for your selection, including English,   
 German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,  
 Simplified Chinese, and Japanese. 
 • Aspect	Control: adjusts the aspect ratio to “Full” or “4:3”. 
 • Information: shows the monitor information. 
 • Reset: “Yes” allows you to restore the default setting. 
 
						

							
3-4Chapter 3: General Instruction  

3.2	 Specifications	summary	(VW195U)
Panel	TypeTFT LCD
Panel	size9" (6:0) wide screen
Max.		ResolutionWXGA+ 440 x 900
Pixel	pitch0.285mm
Brightness	(Typ.)250cd/m2
Brightness	(Max.)300cd/m2
Contrast	Ratio	(Typ.)800:
Contrast	Ratio	(Max.)2000: (with ASCR ON)
Viewing	angle(H/V)	CR>10160˚/160˚
Display	colors6.7M
Response	time2ms (Gray to Gray)
SPLENDID™	Video	EnhancementYes
SPLENDID™	selection5 video preset modes (by hotkey)
Auto	adjustmentYes (by hotkey)
Color	temperature	selection5 color temperatures
Skin-Tone	selection3 skin-tones
Digital	inputDVI-D with HDCP
Analog	inputD-Sub
Audio-in	port3.5 mm Mini-jack
ColorsBlack
Speaker	(Built-in)W x 2 Stereo, RMS
Power	LEDBlue (On)/ Amber (Standby)
VESA	wall	mount00 x 00mm
Tilt-5˚~+20˚
Kensington	lockYes
Voltage	ratingAC: 100~240V
Power	consumptionPower On : < 47W, Standby: < 2W, Power Off: