Asus Vw195nl User Guide

							
1-3ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor 

1.3.2 Back view
1. Audio-in port. This port connects PC audio source by the bundled audio 
cable.
2. AC-IN port. This port connects the power connector from the bundled power 
cord.
3. DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal 
connection.  
4. VGA port. This 15-pin port is for PC VGA connection. 
Rear connectors 
StatusDescription
  BlueON
  AmberStandby mode
  OFFOFF
Stereo speaker
Rear connectors
Stereo speakerScrew holes for VESA Wall Mount
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.
1234
5.  Power button/power indicator
• Press this button to turn the monitor on/off.
• The color definition of the power indicator is as the table below .
Monitor base release button
 
						

							
1-4Chapter 1: Product introduction
 
						

							
2-1ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor 
2.1 Assembling the monitor base
To assemble the monitor base
1. Have the monitor base place on a flat table.
2. Connect the base with the arm according to the below drawing. A click sound 
shows that the base has been connected successfully. 
3. Remove the monitor height adjustment lock.
1
23
The monitor height adjustment lock should NEVER be removed BEFORE you place the monitor VERTICALLY on a flat surface.
 
						

							
2-2Chapter 2: Setup

2.3 Detaching the arm/base (for VESA  
 wall mount)
The detachable arm / base of the VW195xL/VW202xL/VW225xL Series LCD 
monitor is specially designed for VESA wall mount. 
To detach the arm/base
1. Lower the monitor to its lowest height, and then insert the monitor height 
adjustment lock (Figure 1).
2. Have the front of the monitor face down on a table.
3. Remove the rubbers in the four screw holes (Figure 2).
4. Use a screwdriver to remove the two screws on the arm (Figure 2), then slide 
out the arm/base to detach it from the monitor (Figure 3).
2.2  Adjusting the monitor angles
• For optimal viewing, we recommend that you look at the full face of the monitor, 
then adjust the monitor to the angle that is most comfortable for you.
• Hold the base to prevent the monitor from falling when you change its angle.
• You can tilt the monitor’s from -3º to 20º, swivel from left-to-right for 45º, and lift 
the monitor’s height for about 70mm.
 -3º~20º
70mm
45º45º
0º
 
						

							
2-3ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor 

We recommend that you cover the table surface with soft cloth to prevent \
damage to the monitor.
Arm/base
Rubbers in the screw holes 
Two screws 
Figure 2
Figure 3
Figure 1
 
						

							
2-4Chapter 2: Setup

2.5 Connecting the cables
1. Connect the cables as the following instructions:
• To connect the audio cable: connect one end of the audio cable to the  
monitor’s Audio-in port, the other end to the computer's audio-out port. 
• To connect the power cord: connect one end of the power cord securely to 
the monitor’s AC input port, the other end to a power outlet.
• To connect the VGA/DVI cable: 
 a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.  
b. Connect the other end of the VGA/ DVI cable to your computer’s VGA/ 
 DVI port. 
c. Tighten the two screws to secure the VGA/DVI connector.
2.4  Disassembling the monitor base (for  
 product packing)
To disassemble the monitor base
1. Lower the monitor to its lowest height, and then insert the monitor height 
adjustment lock.
2. Have the front of the monitor face down on a table.
3. Press and hold the release button on the monitor base and remove the 
monitor base from the monitor arm.
3
1
 
						

							
2-5ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor 

2.6 Turning on the monitor
Gently press the power button  . See page 1-2 for the location of the power 
button. The power indicator  lights up in blue to show that the monitor is ON.
2. Gather all the cables with the cable hook.
Cable hook
When both the VGA and the DVI cables are connected, you can choose either VGA mode or DVI mode from the Input Select item of the OSD functions.
 
						

							
2-6Chapter 2: Setup
 
						

							
3-1ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor 
3.1 OSD (On-Screen Display) menu 
3.1.1  How to reconfigure
1. Press the MENU button to activate the 
OSD menu. 
2. Press  and  to navigate through 
the functions. Highlight and activate the 
desired function by pressing the MENU 
button. If the function selected has a 
sub-menu, press  and  again to 
navigate through the sub-menu functions. 
Highlight and activate the desired sub-
menu function by pressing the MENU button.
3. Press  and  to change the settings of the selected function.
4. To exit the OSD menu, press the  button. Repeat step 2 and step 3 to 
adjust any other function.  
3.1.2  OSD Function Introduction
1. Spendid
This function contains five sub-functions 
you can select for your preference. Each 
mode has the Reset selection, allowing 
you to maintain your setting or return to 
the preset mode.
• Scenery Mode: best choice for 
scenery photo display with  
SPLENDID™ Video Enhancement.
• Standard Mode: best choice for document editing with SPLENDID™ 
Video Enhancement.
• Theater Mode: best choice for movie with SPLENDID™ Video 
Enhancement.
• Game Mode: best choice for game playing with SPLENDID™ Video 
Enhancement.
• Night View Mode: best choice for dark-scene game or movie with  
SPLENDID™ Video Enhancement.
• In the Standard Mode, the Satuation and Sharpness functions are not user\
-configurable.
• In the other modes, the sRGB function is not user-configurable.
 
						

							
3-2Chapter 3: General Instruction  

3. Color
Select the image color you like from this 
function. 
• Color Temp.: contains five color 
modes including Cool, Normal, Warm, 
sRGB, and User mode.
• Skin Tone: contains three color 
modes including Reddish, Natural, 
and Yellowish. 
In the User mode, colors of R (Red), G (Green), and B (Blue) are u\
ser-configurable; the adjusting range is from 0-100.
• Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows  horizontal disturbances.
• Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image is not proportional.
2.  Image 
You can adjust brightness, contrast, 
sharpness, saturation, position (VGA only), 
ASCR, and focus (VGA only) from this 
main function. 
• Brightness: the adjusting range is 
from 0 to 100.  is a hotkey to 
activate this function.
• Contrast: the adjusting range is from 
0 to 100.
• ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.
• Sharpness: the adjusting range is from 0 to 100.
• Saturation: the adjusting range is from 0 to 100. 
• Position: adjusts the horizontal postition (H-Position) and the vertical 
position (V-Position) of the image. The adjusting range is from 0 to 100.
• Focus: reduces Horizonal-line noise and Vertical-line noise of the image 
by adjusting (Phase) and (Clock) separately. The adjusting range is from 
0 to 100.