Asus Vk248h User Guide

							1-3ASUS VK248 LCD Monitor 
5.  button:
Selects an available input source. • 
6.  Power button/power indicator
Turns the monitor on/off.• 
The color definition of the power indicator is as the below table.• 
StatusDescription
BlueON
AmberStandby mode
OFFOFF
1.4.2 Back view
67
4
Rear connectors
1. AC-IN port. This port connects the power cord.
2. Audio-in port. This port connects PC audio source by the bundled audio 
cable.
3. Earphone jack. This port is only available when an HDMI cable is 
connected.
4. USB upstream port. This port is for connection with a USB upstream cable. 
The cable enables the built-in webcam on the monitor. 
5. HDMI port. This port is for connection with an HDMI compatible device.
6. DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal 
connection.
7. VGA port. This 15-pin port is for PC VGA connection.
Press  (Input Select button) to display HDMI signals after you connect HDMI cable with the monitor.
 
						

							1-4Chapter 1: Product introduction
1.4.3 QuickFit Function
The QuickFit function allows users have a preview of the document or pho\
to layout 
directly on screen without printing test copies. 
To activate Quickfit, press the Quickfit hotkey, and then press the MENU key to 
switch between different pattern sizes. 
Alignment GridLetter
Photo 4x6, 3x5, 2x2Photo 8x10, 5x7
When QuickFit is activated, press the control buttons on the front panel\
 to make 
adjustments. The QuickFit QSD displayed in the lower right corner of the\
 screen 
will guide users to make selections. 
The QuickFit OSD shown on the screen is not accessible by tapping on it.\
 
 
						

							1-5ASUS VK248 LCD Monitor 
 
						

							1-6Chapter 1: Product introduction
 
						

							2-1ASUS VK248 LCD Monitor 
2.1 Assembling the monitor arm/base
To assemble the monitor base:
1. Have the front of the monitor face down on a table.
2. Attach the base with the arm until it clicks into place.
We recommend that you cover the table surface with soft cloth to prevent\
 damage to the monitor.
2.2  Adjusting the monitor
 
For optimal viewing, we recommend that you look at the full face of the \
• 
monitor, then adjust the monitor to the angle that is most comfortable f\
or you.
Hold the stand to prevent the monitor from falling when you change its a\
ngle.
  The recommended adjusting angle is +20˚ to -5˚.
-5f
 to +2 0f
It is normal that the monitor slightly shakes while you adjust the viewi\
ng angle. 
 
						

							2-2Chapter 2: Setup
2.3 Detaching the arm/base (for VESA 
wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall 
mount. 
To detach the arm/base:
1. Have the front of the monitor face down on a table.
2. Remove the rubbers in the four screw holes. (Figure 1)
3. Use a screwdriver to remove the two screws on the arm (Figure 2), then slide 
out the arm/base to detach it from the monitor (Figure 2).
Figure 1
Figure 2
We recommend that you cover the table surface with soft cloth to prevent\
 
damage to the monitor.
 
						

							2-3ASUS VK248 LCD Monitor 
2.4 Connecting the cables
1. Connect the cables as the following instructions:
VGA
DVI
HDMI
Audio-in
USB 2.0
Earphone jack
To connect the audio cable: •	connect one end of the audio cable to the 
monitor’s Audio-in port, the other end to the computer’s audio-out\
 port. 
To connect the power cord•	: connect one end of the power cord securely to 
the monitor’s AC input, the other end to a power outlet.  
To connect the VGA/DVI/HDMI cable•	: 
Plug one end of the VGA/DVI/HDMI cable to the monitor’s VGA/DVI/a. 
HDMI port.
Connect the other end of the VGA/DVI/HDMI cable to your computer's b. 
VGA/DVI/HDMI port.
Tighten the two screws to secure the VGA/DVI connector. c. 
To use the webcam: •	connect the upstream port of the monitor and the USB 
port of your computer with the supplied USB cable.
To use the earphone (only when an HDMI cable is connected)•	: connect the 
end with plug type to the monitor’s earphone jack. 
When these cables are connected, you can choose the desired signal from \
the 
Input Select item in the OSD menu.
 
						

							2-4Chapter 2: Setup
2. Gather all the cables with the cable management slot.
2.5  Turning on the monitor
Press the power button  . See page 1-2 for the location of the power button. The 
power indicator  lights up in blue to show that the monitor is ON.
cable management slot
 
						

							2-5ASUS VK248 LCD Monitor 
 
						

							2-6Chapter 2: Setup