Asus Router WL-500W User Manual

							
WL-500W Wireless Router User Manual
2

5. Input  the  IP  address  of  WL-500W  in the Printer  Name  of  IP  Address  field and click Next.
6. Select Custom and click Settings.
7. S e t  P r o t o c o l  t o  L P R  a n d   t y p e LPRServer in Queue Name field. Click Next to continue.
8. Press Next  to  finish  standard  TCP/IP port setting.
3. Select Create a new port and set Type of  port  to Standard  TCP/IP  Port,  then click Next.
4. C l i c k N e x t  t o  s e t u p  T C P / I P  p o r t  f o r accessing the network printer. 
						

							
WL-500W Wireless Router User Manual
30

9. Press Finish  to  complete  the  settings and return to Add Printer Wizard.
10. Install  printer  driver  from  the  vendor-model  list.  If  your  printer  is  not  in  the list, click Have Disk to manually assign the location of driver. 
11. Click Next  to  accept  the  default  name for the printer.12. Select Yes  to  print  a  test  page.  Click Next to print.
13. T h e  i n s t a l l a t i o n  i s  c o m p l e t e .  C l i c k Finish to quit the Add Printer Wizard. 
Note:  If  you  use  Windows®  98  or  ME  which  does  not  support  Standard TCP/IP  port, you need to use Remote Port which is supported by WL-500W.
Note: If you have already installed the printer locally on your computer, right click the printer icon and select Property -> Port tab to add a standard TCP/IP port. Click Add Port then select Standard TCP/IP Port and click New Port button. Refer to step 5-8 for setting procedures. 
						

							
WL-500W Wireless Router User Manual
3

1) Utility Installation for WL-500W
1. Click Install  ASUS  Wireless  Router Utilities  to  run  the  setup  installation program.
2. Click Next to continue.
3. C l i c k N e x t  t o  i n s t a l l  t h e  u t i l i t y  i n  t h e designated location.4.  Select a program folder and click Next.
5.  Press Finish to quit the installation program.6.  Open the EZSetup Wizard.
6. Setting up using ASUS utility 
						

							
WL-500W Wireless Router User Manual
32

Wireless  settings,  including  network  name  and  network  keys,  are  generated  automatically. You  can  modify  these  settings  manually.  Note  if  your  wireless  router  is  configured  before, select Preserve  original  wireless  router  settings  to  use  the  current  value.  Click Next  to continue.
Click the EZSetup button in the utility.
2) EZSetup
Wireless LAN setup will complete in two easy steps. First open the EZSetup utility 
form Start menu, then push the EZSetup button on the rear panel for 3 se\
conds.
1)  If the setup button is pushed without running the EZsetup wizard ut\
ility, the PWR indicator will flash and Internet connections will pause for a short period but will then return to normal operation without change.      2) To use EZSetup, we recommend using an ASUS wireless adapter such as WL-100W, WL-100gE, and WL-169gE.
Note:  Use  EZSetup  Wizard  with  one wireless client at a time. If the wireless client  computer  cannot  discover  the w i r e l e s s  r o u t e r  w h i l e  i n  E Z S e t u p mode,  please  shorten  the  distance between the client and the router.
Push EZSetup over 3 sec. and release.
2
3 
						

							
WL-500W Wireless Router User Manual
33

If  you  need  to  configure  the  ISP  settings  for  your  wireless  router,  select Configure  ISP settings, click Next and follow the instructions to complete the settings.
Setup is complete, press Print/Save Wireless LAN  Settings  button  for  future  reference. Click Finish to exit the EZSetup utility.
4
5 
						

							
WL-500W Wireless Router User Manual
34

7. Troubleshooting
Cannot access to web browser for router configuration
1 .   O p e n   a   w e b   b r o w s e r   a n d   o p e n "Internet Options" dialog box.
2.  Click  on  "Delete  Cookies"  and  "Delete Files".
Cannot Establish Connection via Wireless
 Out of Range:
 •  Put the router closer to the wireless client.
 •  Try to change the channel setting.
  Authentication:
 •  Use wired connection to connect to router. 
 •  Check the wireless security setting.
•   Do the hard reset on the wireless router by pressing the Reset button on the rear\
 panel for more than 5 seconds.
  Couldn't find the router:
• Do the hard reset on the wireless router by pressing the Reset button on the rear panel for more than 5 seconds.
 • Check the setting in the wireless adapter such as SSID and encrypti\
on setting.
Cannot get access to the Internet via wireless LAN adapter
 • Move the router closer to the wireless client.
• Check whether the wireless adapter is connected to the correct AP.
 • Check whether the wireless channel in use conforms to the channels \
available in your country/ area.
 • Check encryption setting.
 • Check whether the ADSL or Cable connection is correct.
 • Retry using another Ethernet cable. 
						

							
WL-500W Wireless Router User Manual
35

Internet is not accessible
• Check the lights on ADSL modem and the Wireless Router.
•  Check whether the "WAN" LED on the Wireless Router is ON. If the LED is not ON, change the cable and try again.
When  ADSL  Modem  "Link"  light  is  ON  (not  blinking),  this  means  Internet 
Access is Possible.
• Restart your computer.
• Refer to the Quick Setup Guide of the wireless router and reconfigu\
re the settings.
• Check whether the WAN LED on the router is ON or not.  
• Check wireless encryption settings.
• Check whether the computer can get the IP address or not (via both wired network and wireless network).
• Make sure your Web browser is configured to use the local LAN, and is not configured to use a proxy server.
If  the  ADSL  "LINK"  light  blinks  continuously  or  stays  off,  Internet  access  is 
not  possible  -  the  Router  is  unable  to  establish  a  connection  with  the  ADSL 
network. 
• Make sure your cables are all correctly connected .
• Disconnect the power cord from the ADSL or Cable modem, wait a few minutes, then reconnect the cord.
• If the ADSL light continues to blink or stays OFF, contact your ADSL service provider.
Network name or encryption keys are forgotten
•  Try to setup the wired connection for setup the wireless encryption again\
.
•  Do the hard reset on the wireless router by pressing the Reset button on the rear panel for more than 5 seconds.
How to reset to defaults
The  following  are  factory  default  values.  If  you  push  the  Restore  button  on  the  back  of  the ASUS Wireless Router for over 5 seconds, or click the “Restore” button on the “Factory Default”  page under “ Advanced Setup”, the following default settings overwrite the old settings on your wireless router.
  User Name:     admin        Subnet Mask:  255.255.255.0
 Password:     admin        DNS Server 1:  192.168.1.1
 Enable DHCP:   Yes (if plug in Wan cable)  DNS Server 2:  (Blank)
 IP address:     192.168.1.1      SSID:     default
 Domain Name:   (Blank) 
						

							
WL-500W Wireless Router User Manual
36

8. Appendix
FCC Warning Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and
(2)  this  device  must  accept  any  interference  received,  including  interference  that  may  cause undesired operation.
This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  class  B  digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This  equipment  generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio communications. However, there is no guarantee that interference will not occur in a particular installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or  television  reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: 
Any  changes  or  modifications  not  expressly  approved  by  the  party  responsible  for  compliance could void the user’s authority to operate the equipment.
Prohibition of Co-location
This  device  and  its  antenna(s)  must  not  be  co-located  or  operating  in  conjunction  with  any  other antenna or transmitter.
Safety Information
To  maintain  compliance  with  FCC’s  RF  exposure  guidelines,  this  equipment  should  be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna.
Declaration of Conformity for R&TTE directive /5/EC
Essential requirements – Article 3
Protection requirements for health and safety – Article 3.1a 
						

							
WL-500W Wireless Router User Manual
37

Te s t i n g  f o r  e l e c t r i c  s a f e t y  a c c o r d i n g  t o  E N  6 0 9 5 0 - 1  h a s  b e e n  c o n d u c t e d .  T h e s e  a r e considered relevant and sufficient.
Protection requirements for electromagnetic compatibility – Article 3.1b
Testing for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-17 has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing  for  radio  test  suites  according  to  EN  300  328-  2  has  been  conducted.  These  are considered relevant and sufficient.
CE Mark Warning
T h i s  i s  a  C l a s s  B  p r o d u c t ,  i n  a  d o m e s t i c  e n v i r o n m e n t ,  t h i s  p r o d u c t  m a y  c a u s e  r a d i o interference, in which case the user may be required to take adequate me\
asures.
GNU general public license
Licensing information
This  product  includes  copyrighted  third-party  software  licensed  under  the  terms  of  the  GNU General  Public  License.  Please  see  The  GNU  General  Public  License  for  the  exact  terms and conditions of this license. We include a copy of the GPL with every CD shipped with our product.  All  future  firmware  updates  will  also  be  accompanied  with  their  respective  source code.  Please  visit  our  web  site  for  updated  information.  Note  that  we  do  not  offer  direct support for the distribution.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
Everyone  is  permitted  to  copy  and  distribute  verbatim  copies  of  this  license  document,  but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it.    By  contrast,  the  GNU  General  Public  License  is  intended  to  guarantee  your  freedom  to share  and  change  free  software--to  make  sure  the  software  is  free  for  all  its  users.    This General  Public  License  applies  to  most  of  the  Free  Software  Foundation’s  software  and  to any other program whose authors commit to using it.  (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.)  You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price.  Our General Public Licenses  are  designed  to  make  sure  that  you  have  the  freedom  to  distribute  copies  of  free software  (and  charge  for  this  service  if  you  wish),  that  you  receive  source  code  or  can  get  it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. 
						

							
WL-500W Wireless Router User Manual
38

To  p r o t e c t  y o u r  r i g h t s ,  w e  n e e d  t o  m a k e  r e s t r i c t i o n s  t h a t  f o r b i d  a n y o n e  t o  d e n y  y o u these  rights  or  to  ask  you  to  surrender  the  rights.  These  restrictions  translate  to  certain responsibilities for you if you distribute copies of the software, or if\
 you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have.  You must make sure that they, too, receive or can get the source code.  And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software.  If the software is modified by someone else and passed  on,  we  want  its  recipients  to  know  that  what  they  have  is  not  the  original,  so  that  any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents.  We wish to avoid the danger  that  redistributors  of  a  free  program  will  individually  obtain  patent  licenses,  in  effect making the program proprietary.  To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow. 
Terms & conditions for copying, distribution, & modification
0. This  License  applies  to  any  program  or  other  work  which  contains  a  notice  placed  by the  copyright  holder  saying  it  may  be  distributed  under  the  terms  of  this  General  Public License.    The  “Program”,  below,  refers  to  any  such  program  or  work,  and  a  “work  based on  the  Program”  means  either  the  Program  or  any  derivative  work  under  copyright  law: that  is  to  say,  a  work  containing  the  Program  or  a  portion  of  it,  either  verbatim  or  with modifications and/or translated into another language.  (Hereinafter, translation is included without limitation in the term “modification”.)  Each licensee is addressed as “you”.   
 Activities other than copying, distribution and modification are not covered by this License; they  are  outside  its  scope.    The  act  of  running  the  Program  is  not  restricted,  and  the output  from  the  Program  is  covered  only  if  its  contents  constitute  a  work  based  on  the Program  (independent  of  having  been  made  by  running  the  Program).  Whether  that  is true depends on what the Program does. 
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it,  in  any  medium,  provided  that  you  conspicuously  and  appropriately  publish  on  each copy  an  appropriate  copyright  notice  and  disclaimer  of  warranty;  keep  intact  all  the notices  that  refer  to  this  License  and  to  the  absence  of  any  warranty;  and  give  any  other recipients of the Program a copy of this License along with the Program.\
 You  may  charge  a  fee  for  the  physical  act  of  transferring  a  copy,  and  you  may  at  your option offer warranty protection in exchange for a fee. 
2.  You  may  modify  your  copy  or  copies  of  the  Program  or  any  portion  of  it,  thus  forming  a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these condi\
tions:
 a) You  must  cause  the  modified  files  to  carry  prominent  notices  stating  that  you  changed the files and the date of any change.