Asus Router WL-320gP User Manual

							
1. Introduction
ASUS 802.11g Access Point11
Chapter 1 - Introduction

1..3  Roaming Between ASUS APs
If there are multiple ASUS APs on the network, then a wireless mobile client 
may seamlessly roam from one ASUS AP to another.
Each  ASUS  AP  creates  its  own  wireless  cell  or  coverage  area.  This  is 
also  known  as  a  Basic  Service  Set  (BSS). Any  wireless  mobile  client  can 
communicate  with  a  particular  ASUS  AP  if  it  is  within  the  ASUS  AP’s 
coverage area.
If the cells of multiple ASUS APs overlap, then the wireless mobile client 
may  switch  from  one  ASUS  AP  to  another  as  it  travels  throughout  the 
facility.  During  the  hand-off  from  one ASUS AP  to  another,  the  wireless 
mobile  client  maintains  an  uninterrupted  connection  to  the  network.  This 
is known as “roaming.”
Multiple  ASUS  APs  connected  to  a  common  Ethernet  network  form  an 
Extended Service Set (ESS). All members of an Extended Service Set are 
configured with an ID, known as the SSID or ESSID. Wireless mobile clients 
must be configured with the same SSID as the ASUS APs on the network. A 
client can only roam between ASUS APs that share the same SSID.
1..  Roaming Guidelines
•   An ASUS WLAN Card can only roam between APs of the same type. 
•   All ASUS APs must have the same SSID.
•   All computers with ASUS WLAN Cards must have the same SSID as 
the Access Points that they will roam.
•   If WEP  encryption  is  enabled,  then  all ASUS APs  and  client  adapters 
must use the same encryption level and WEP Key(s) to communicate.
•   The  ASUS  APs’  cells  must  overlap  to  ensure  that  there  are  no  gaps 
in  coverage  and  to  ensure  that  the  roaming  client  will  always  have  a 
connection available.
•   ASUS APs  that  use  the  same  Channel  should  be  installed  as  far  away 
from each other as possible to reduce potential interference.
•   It is strongly recommended that you perform a site survey using the utility 
provided with the ASUS WLAN Card to determine the best location for 
each ASUS AP in the facility. 
						

							
1. Introduction
Chapter 1 - Introduction
12ASUS 802.11g Access Point

1.  Getting to Know the WL-320gP
1..1   Front panel features
The ASUS WL-320gP Access Point includes LED indicators which show 
the system, LAN, wireless network, and link status.
PWR (Power)
OFF:    No power or performing boot sequence
ON:   System ready
Blinking: Firmware upgrade failed
LAN (Ethernet Network)
OFF:   No power
ON:   Physical connection to an Ethernet network
Blinking: Transmitting or receiving data (through Ethernet cable)
AIR (Wireless Network)
OFF:   No power
ON:   Wireless function ready
Blinking: Transmitting or receiving data (through wireless)
PWRLANAIRLINK 
						

							
1. Introduction
ASUS 802.11g Access Point13
Chapter 1 - Introduction

1..2  Rear panel features
The rear panel contains the Ethernet, the DC port, and the Reset button.\
LabelDescription
ETHERNETThe Ethernet port connects to an Ethernet device such as to a switch (either Power over Ethernet support or not) or to a router.
RESETPress the Reset button to restore to factory default settings.
DCThe DC port connects to the power adapter This port will not be used if using Power over Ethernet switch or injector.
LINK (Link Status)
Operation ModeAP/Repeater/Bridge/GatewayClient
OFFClient not associatedNot associated to AP
ONClient associatedAssociated to AP with strong signal
Blinking quickly--Associated to AP with better signal
Blinking slowly--Associated to AP with weak signal 
						

							
Chapter 2 - Hardware Installation
2. Hardware
1ASUS 802.11g Access Point

2.   Installation
This chapter describes the installation procedure for the ASUS 802.11g AP 
and includes a description of the LEDs found on the unit.
2.1  Installation Procedure
Follow these steps to install the ASUS 802.11g WLAN AP.
1.  Determine the best location for the ASUS 802.11g WLAN AP. Keep in 
mind the following considerations:
•  The maximum length of the Ethernet cable that connects the Access 
Point to the network is 100 meters.
•  For standard placement, try to place the Access Point on a flat, sturdy 
surface as far from the ground as possible, such as on top of a desk or 
bookcase, keeping clear of metal obstructions and away from direct 
sunlight.
•  For external antenna mounting, install the external antennas so that 
they are clear of obstructions. Refer to the documentation that came 
with the antennas for mounting and installation instructions.
•  Try to centrally place the Access Point or its antennas so that it will 
provide coverage to all of the wireless mobile devices in the area.
•  Use  only  the  power  supply  that  came  with  this  unit.  Other  power 
supplies may fit but the voltage and power may not be compatible.
Note: The ASUS 802.11g AP must be operated at least 20 centimeters 
from any person. This is necessary to ensure that the product is oper-
ated in accordance with the RF Guidelines for Human Exposure which 
have been adopted by the Federal Communications Commission.
2.  Place  the Access  Point  in  the  desired  location.  Wall  mounting  is  also 
possible for the Access Point. Refer to the section entitled “Wall Mounting 
Option” on the next page for details.
3.  Attach one end of an RJ-45 Ethernet cable to the Access Point and attach 
the other end to the RJ-45 10Base-T port of a network hub, switch, router, 
or patch panel (possibly on a wall). 
						

							
2. Hardware
Chapter 2 - Hardware Installation
ASUS 802.11g Access Point1

4.  Attach one end of the AC power adapter to the back of the ASUS 802.11g 
AP and the other end to a power outlet.
Note: Use the Access Point only with the power adapter supplied in 
the product package. Using another power supply may damage the 
Access Point.
The Power LED on the front of the Access Point will light up when the unit 
is powered ON. The green Link LED will turn ON to indicate that the Access 
Point has a physical Ethernet network connection.
2.2   Wall Mounting Option
The  ASUS  WL-320gP  Access  Point  is  designed  to  sit  on  a  raised  flat 
surface like a file cabinet or a book shelf. The unit may also be converted 
for mounting to a wall.
To mount the ASUS 802.11g WLAN AP  
to a wall:
1.  Look  on  the  underside  for  the  two 
mounting hooks.
2.  Mark two holes on the wall.
3. In  the  marked  holes  on  the  wall, 
tighten two screws until only 1/4” is 
showing.
4. Latch the hooks of the ASUS WL-320gP onto the screws. 
Note: Readjust the screws if you cannot latch the Access Point onto 
the screws or if it is too loose. 
						

							
3. Software
16ASUS 802.11g Access Point
Chapter 3 - Software Configuration

3.   Software Configuration
3.1   Configuring the ASUS 802.11g AP
The ASUS 802.11g AP can be configured to meet various usage scenarios. 
Some of the factory default settings may suit your usage; others may need 
changing. Prior to using the ASUS 802.11g AP, you must check the basic 
settings to guarantee it will work in your environment. 
Configuring  the  ASUS  802.11g  AP  is  done  through  a  web  browser.  You 
need a Notebook or a PC connected to the ASUS 802.11g AP (either directly 
or through a hub) and running a web browser  as a configuration terminal. 
The connection can be wired or wireless. For the wireless connection, you 
need an IEEE 802.11g/b compatible device, suck as an ASUS WLAN Card, 
installed in your Notebook or PC. You should also disable WEP and set the 
SSID to “default” for your wireless LAN device.
If you want to configure the ASUS 802.11g AP or want to access the Internet 
through the ASUS 802.11g AP, the TCP/IP settings must be correct. Normally, 
the TCP/IP setting should be on the IP subnet of the ASUS 802.11g AP. 
Note:  Changing  TCP/IP  settings  may  require  rebooting  your  PC. 
When rebooting, the ASUS 802.11g AP should be switched ON and 
in the ready state. 
						

							
3. Software
ASUS 802.11g Access Point17
Chapter 3 - Software Configuration

Advanced IP Settings
If you want to set your IP address manually, the following default settings 
of the ASUS 802.11g AP should be known:
• IP address 192.168.1.1  
• Subnet Mask 255.255.255.0. 
If you set your computer’s IP manually, it needs to be on the same segment.  
For example:
•  IP address 192.168.1.xxx (xxx can be any number between 2 and 254 that is 
not used by another device)
•  Subnet Mask 255.255.255.0 (same as the ASUS 802.11g AP)
•  Gateway 192.168.1.1 (this is the ASUS 802.11g AP IP address)
•  DNS 192.168.1.1 (ASUS 802.11g AP IP address or your own). 
						

							
3. Software
18ASUS 802.11g Access Point
Chapter 3 - Software Configuration
3.2  ASUS WLAN Utilities
Installing the UtilityTo  install  the ASUS  WLAN  Utilities  in  Microsoft®  Windows,  insert  the  support  CD  in  the  CD 
drive. If Autorun is disabled, run setup.exe from the root directory of the suppor\
t CD.
(2) Click Next.
(3)  Click Next to  accept  the  default 
destination folder or click Browse to 
specify another path.
(4)  Click Next to  accept  the  default 
program  folder  or  enter  another 
name.
(1) Click Install...Utilities.
(5) Click Finish when setup is 
complete. 
						

							
3. Software
ASUS 802.11g Access Point1
Chapter 3 - Software Configuration
WLAN Utilities
After installation, you can launch the utilities through the Start menu.\
Wired Ethernet Connection
Besides using a network hub, you can also connect a LAN cable from your 
computer to the ASUS 802.11g AP using either a straight or crossover cable 
since the ASUS 802.11g AP has auto-crossover capability. 
Wireless Connection
If  you  are  using  a  Notebook  with  a  wireless  adapter,  you  can  connect  to 
the ASUS WLAN Web Manager without a wired Ethernet connection. Just 
make sure your TCP/IP settings are set correctly. 
						

							
3. Software
20ASUS 802.11g Access Point
Chapter 3 - Software Configuration
WLAN Utilities

If  your  computer’s  IP  is  not  on  the 
same  subnet  as  the  ASUS  802.11g 
AP (192.168.1.X), you will be asked 
to  change  it.  The  last  digit  in  the  IP 
address can be any number from 2 to 
254 that is not used by another device. 
Gateway is not required.
Manually Entering the Address
You can also open your PC’s web browser and enter the default IP address 
of the ASUS 802.11g AP : http://192.168.1.1 
Device Discovery
Run  the ASUS WLAN Device  Discovery from  the Start menu  and  click 
Config on the device.
(This is the correct setting.)(This is the wrong setting.)
Note: You can also change your TCP/IP settings through the Windows 
network properties. Refer to page 17.