Asus Router DSL-N13 User Manual Czech Version

							
DSL-N13	Wireless	ADSL	2/2+	Modem	Router	User	Manual
4

5.  Input the IP address of DSL-N13 in 
the Printer 	Name 	of 	IP 	Address 
field and click Next.
6.   Select Custom and click Settings...
7.  S e t P r o t o c o l  t o L P R  a n d  t y p e 
LPRServer  in Queue 	Name  field. 
Click Next to continue.
8.   Press Next  to  finish  standard TCP/
IP port setting.
9.  P r e s s F i n i s h  t o  c o m p l e t e  t h e 
settings  and  return  to  Add  Printer 
Wizard.
10.  Install printer driver from the vendor-
model  list.  If  your  printer  is  not  in 
the list, click Have 	Disk to manually 
assign the location of driver.  
						

							
DSL-N13	Wireless	ADSL	2/2+	Modem	Router	User	Manual
50

11. Click Next to accept the default name for the printer.12. Select Yes to print a test page. Click Next to print.
13. The installation is complete. Click Finish to quit the Add Printer Wizard. 
If  you  use  Windows®  98  or  ME  which  does  not  support  Standard  TCP/IP 
port, you need to use Romote Port which is supported by DSL-N13.
If you have already installed the printer locally on your computer, right click 
the  printer  icon  and  select Property ->	Port  tab  to  add  a  standard TCP/IP 
port. Click Add 	Port then select Standard 	TCP/IP 	Port and click New 	Port 
button. Refer to Step 5-8 for setting procedures. 
						

							
DSL-N13	Wireless	ADSL	2/2+	Modem	Router	User	Manual
51

This chapter describes how to maintain your DSL-N13 wireless ADSL router.
Configuration backup
You  can  backup  the  configuration  to  a  file  and  store  it  on  your  computer.  Click 
Management 	-> 	Settings  to  open  the  configuration  page  and  click  the Backup 	
Settings  button.  Click Save  and  define  the  destination  folder.  The  default  name  for 
backup file is backupsettings.conf.
Management
Restore settings from a backup file
You can restore the settings from a backup file when you have reset the wireless router 
to factory default. Click Management 	-> 	Settings 	-> 	Update to open the configuration 
page.  Click Browse... 	to  locate  the  backup  file  on  your  computer,  then  click Update	
Settings  button  to  proceed.  When  restoring  is  complete,  the  wireless  router  reboots. 
The whole process takes about 80 seconds.
Reset	to	factory	default
If you want to clear all settings and return to the factory default settings. You can press 
the Reset	button  on  the  rear  panel  of  the  wireless  router  for  10  seconds;  or  click 
Management 	-> 	Settings 	-> 	Restore 	Default 	to open the configuration page and click 
the Restore 	Default 	Settings 	button. 
						

							
DSL-N13	Wireless	ADSL	2/2+	Modem	Router	User	Manual
52
Setting	up	time	server
You can configure the time setting so that DSL-N13 can always synchronize with a time 
server  from  Internet.  Click Management 	-> 	Time 	settings  and  check Automatically 	
synchronize	with 	International 	servers. Select a time server from the drop-down list 
and set your time zone. When finished, click Save/Apply.
Firmware	update
To update firmware, click Management 	-> 	Update 	Software. Click Browse... to locate 
the  firmware  file,  then  click Update 	Software  button  to  start  uploading  the  firmware. 
The update process takes about two minutes.