Asus M6000 Service Guide

							DISASSEMBLY PROCEDURE 
 
10. Remove 1 screw (M2.5*4L(K)) and 1 screw on the other side, then take right and lift  
hinge off. 
 
M2.5*4L M2.5*4L 
 
11. Remove 2 tapes and dissconnect coaxial cable then take it away. 
 
 
12. Finally, Remove 4 screws(M2*3L(K)) on the right LCD bracket , and 4 screws on the ilft 
side to disassemble LCD brackets. 
 3 - 11  
						

							DISASSEMBLY PROCEDURE 
 
M2*3L 
M2*3L 
 
Top Case Module 
The illustrations below show how to disassemble and remove the top case module 
of the notebook. 
 
Removing Top Case Module  TOP CASE 
MODULE 
REMOVE 
 
1. Remove 5 screw pads and 5 screws(M2*3L*(K)) on top side. 
 
M2*3L 
 
 
2. Remove 7 screws (M2*6L(K)) on top case and 16 screws (M2*3L(K)+M2*6L(K)) on 
bottom case. 
 
M2*6L 
M2*3L 
 3 - 12  
						

							DISASSEMBLY PROCEDURE 
             
 
Removing touch pad 
3. Loosen the touch pad FPC cable then separate the top case module from the bottom 
case module. 
 
 
4. Disconnect touch pad FPC cable and remove 5 screws(M2*3L(K)) then take touch pad 
backet off and take touch pad away. 
 
M2*6L 
M2*3L M2*6L 
M2*3L 
 
Motherboard module MOTHERBOARD 
MODULE 
 MDC MODULE 
REMOVAL 
The illustrations below show how to disassemble and remove the Motherboard module 
 
Removing Motherboard Module 
1. Remove the audio DJ and 3 screws (M2*6L(K)). 
 3 - 13  
						

							DISASSEMBLY PROCEDURE 
    
 
2. Take the VGA heat sink module away and remove 2 tapes then disconnect modem cable. 
    
M2*6L 
MOTHERBOARD 
REMOVAL 
 
3.  Loosen the audio FPC and FAN cable. 
 
 
 
4.  Remove 1 screw(M2*6L(K)) then take the optical drive FPC away. 
 3 - 14  
						

							DISASSEMBLY PROCEDURE 
 
M2*6L 
 
5.  Take the optical drive FPC away and remove 6 screws(M2*6L(K)).  
 
M2*6L 
 
6.  Remove the audio FPC and pull out the card reader dummy & PCMCIA dummy. Finally, pull 
out the motherboard from the bottom case carefully. 
 
 
 3 - 15  
						

							DISASSEMBLY PROCEDURE 
 
 
 
 
Bottom Case Module  BOTTOM 
CASE 
MODULE 
The illustrations below show how to disassemble and remove the bottom case 
module of the notebook. 
 
1. Remove 2 screws(M2*3L(K)) then take the modem board away. 
 
M2*3L 
 
2.  Remove 1 screw tape then loosen the speaker cable. 
 
 
3. Remove 1 screw (M2*3L(K)) then take the LED board away. 
 3 - 16  
						

							DISASSEMBLY PROCEDURE 
 
M2*3L 
 
4. Remove 1 screw (M2*6L(K)) then remove the MIC out the hole and pull out the audio 
board upward then take it away. 
 
M2*6L 
 
5. Remove 1 tape then take the MIC away. 
 
 
6. Use tweezers to lift modem cable up then take it away 
 3 - 17  
						

							DISASSEMBLY PROCEDURE 
 
 
7. Remove 1 screw (M2*6L(K)) and 1 screw on the other side and then take 2 speakers 
away. 
 
M2*6LM2*6L 
 
8.  Finally, Remove 2 screws (M2.5*4L(K)) then take the FAN module away. 
 
M2.5*4L 
 3 - 18