ASK Impression 860 User Guide

							USER GUIDELCD PROJECTOR40 12 CONNECTORS
The connector ports for the source equipment on the LCD projector are
located on the right hand-side (when facing) of the unit.  The connector
port for the mains power cord is located next to the fuse cabinet.  The
pinouts of all the connector ports is described in this section.Do not connect any devices or cables other than those
supplied with the LCD projector into the connector ports on
the projector unit, even if the connector ports appear identical,
as this voids any warranty and may cause permanent damage
to the projector.SOURCE 1SOURCE 2SOURCE 3MOUSE12.1 SOURCE 1/2/3
These connectors relay all sync signals from the computer to the
projector, and also to a local CRT monitor if required.12345ANALOG R INANALOG G INANALOG B INNOT USED678ANALOG R OUT110199182626 PIN HIGH DENSITY DSUBFEMALE (FRONT VIEW)91011121415ANALOG G OUTANALOG B OUTANALOG R GND INANALOG G GND INANALOG B GND IN16171819202122ANALOG R GND OUTANALOG G GND OUTANALOG B GND OUTHSYNC IN23242526C/VSYNC INDIGITAL GNDPCID0PCID1DIGITAL GNDHSYNC OUTVSYNC OUT13NOT USEDNOT USEDNOT USEDNOT USEDNOT USED 
						

							USER GUIDELCD PROJECTOR41 12.2 MOUSE
This port is used to exchange mouse messages between the projector
and the computer.8 PIN MINIDINFEMALE(FRONT VIEW)1234567812345PS/2 CLOCKRS232 TXDRS232 RTSRS232 RXDRS232 CTS678PS/2 DATAMAC ADBGND 
						

							USER GUIDELCD PROJECTOR42 13 ENVIRONMENTAL STATEMENT
Care has been taken in the manufacture of this LCD projector that
environmental stress and pollution has been minimized.  Where possible,
recyclable materials have been used to minimize the environmental
impact.
There are no special requirements for handling the product.  Should the
LCD module inside the projector become broken for any reason, resulting
in a spillage of liquid and glass fragments from inside the unit, the
following precausions should be taken:
· wear gloves,
· place the projector unit without opening it inside a heavy-duty
polythene bag to retain any further spillage,
· clean up the spillage, disposing of the waste wisely, and wash your
hands thoroughly.
The delivery packaging can be recycled without further ado.  With
respect to the LCD projector unit itself, thought should be given to the
eventual disposal of the unit in the most environmentally friendly manner
considering the mechanical, electronic and chemical components inside. 
						

							USER GUIDELCD PROJECTOR43 14 FCC STATEMENT
This equipment has been certified to comply with the limits for a Class A
computing device, pursuant to Subpart J of Part 15 of FCC rules. Only
peripherals (computer input/output devices, terminals, printers, etc.)
certified to comply with the Class A limits may be attached to a computer
that complies with Class A limits. When connecting to a peripheral
device, a shielded input/output cable is required to ensure compliance
with FCC rules. The shielded cable that must be used is supplied with the
equipment. Operation with non-certified peripherals or non-shielded
cables is likely to result in interference to radio and TV reception.
This equipment generates and uses radio-frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
interference to radio and television reception. It has been tested and
found to comply with the limits for a Class A computing device in
accordance with the specifications in Subpart J of Part 15 of the FCC
rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures :
· Reorient the receiving antenna.
 
· Relocate the projector with respect to the receiver.
 
· Plug the equipment to a different outlet so that equipment
and receiver are on different branch circuits.
 
· Fasten cables using mounting screws to ensure adequate EMI
control.
You may require the following booklet from the Federal Communications
Commission (FCC) : How to identify and resolve radio and TV
interference problems, available from the U.S. Government Printing
Office, Washington, DC 20402, Stock No. 004-000-00345-4. 
						

							USER GUIDELCD PROJECTOR44 15 SERVICE INFORMATIONThis product contains no user serviceable parts, outside the
scope of section  Maintenance. Attempts to modify
mechanics, electronics or optics inside the housing will violate
any warranties, and may be hazardous.If for any reason the product fails to work properly, first check the section
on Trouble-shooting. If the LCD projector still do not work to
specification, please contact your dealer for technical support. Prepare a
list of the symptoms you observe to make the diagnosing easier for your
dealer.
In cases where a problem cannot be solved by the assistance of your
dealer, please call the following number to get an RMA (Return Materials
Authorization) :
ASK AS, Headquarters :
+ 47 69340155 (Norway)
Fax : +47 69340632
ASK LCD Inc.
North and South American Office :
1-201-896-8888 (USA)
Fax: 1-201-896-0012Be sure to include your RMA number on the outside of the
shipping box, as units without this number will be returned to
sender without processing.Remember to include all cables and power supply when
returning the goods.