ASK Impression 750 User Guide

USER GUIDELCD PROJECTOR10 5.2 MOUSE
See the rear foldout when setting up.
Connect the mouse to the LCD projector using the appropriate adapter (5)
as described in the table below. Then connect the adapter (5) to the mouse
cable (1) at the computer end. Finally, connect the mouse cable (1) to the
LCD projector.
For the computer to recognise the mouse, connect the mouse before
power is applied.
A Y-split is provided with the PC and MAC adapters that enables parallel
use of the local computer mouse and the...

USER GUIDELCD PROJECTOR11 USING THE BATMOUSE:
STEPOPERATION1Control mouse pointer directly with the cursor keys2Press LEFT to activate (emulates the left mouse key)3Press DRAG to tag an object, move it using the cursor keys,
then press DRAG again (or wait 5 seconds) to release the
object (Drag-and-Drop).4Press RIGHT if your application requires emulation of the
right mouse key.The centre key of three-key mice is not supported.
If double-click does not work properly, try to adjust the double-click rate...

USER GUIDELCD PROJECTOR12 5.3 AUDIO AND VIDEO
Connect the LCD projector to a video source as shown in the rear foldout.
Use a TV set as a local video monitor if desired (the data monitor may not
be used as a video monitor).
Connect the AV cable (6) to the AUDIO and VIDEO connectors on the LCD
projector. Then connect the AV cable to the audio out connectors and
video out connector on the video source. Connect sound to the correct
AUDIO channel (S-VIDEO or VIDEO).
S-VIDEO, often referred to as S-VHS, may...

USER GUIDELCD PROJECTOR13 6 USING THE LCD PROJECTOR
The LCD projector has a set of connectors and controls that you need to
know in order to operate the device correctly.
6.1 OPTICS
The projection lens is mounted in the front of the projector. The optical
system is designed with a 12 degree keystone correction so that the
projected image is shifted upwards on the wall. This in effect enables the
placement of the projector on a flat table, still getting a rectangularly
projected image on the wall.Avoid...

USER GUIDELCD PROJECTOR14 6.3 REMOTE CONTROL
The infrared BatMouse remote control (RC) is the main user interface to
the device. The RC is used to set the LCD projector correctly (to get the
best possible viewing conditions) and to control the presentation.
The figure shows the different keys of the BatMouse.Set-up should be done once with the application(s) you are running most
frequently. Allow some minutes for the equipment to warm up before
adjusting. Most settings will automatically be memorized...

USER GUIDELCD PROJECTOR15 The MEM column in the tables below indicates whether the setting is
memorized for each source. A short-form description is outlined in the
table below. For a detailed overview, please see the Features section.
BATMOUSE KEYS :
CONTROLFUNCTIONMEMCONTRContrast (ratio between light and dark colors)YESBRIGHTBrightness (whiteness)YESVOLUMESound volume controlYESON/OFFTurns the projector on/off-RESETDefaults to standard settings-BLACKBlackens the screenNOPROGThis key may be programmed...

USER GUIDELCD PROJECTOR16 6.4 CONTROL PANEL
The control panel keyboard consists of  a subset of  the remote control
keys. For a detailed overview, please see the Features section.LAMP CHANGERRESET
TUNEON/OFFSPARE LAMPBRIGHT
CONTROLFUNCTIONTUNEAdjusts the stability of the imageBRIGHTAdjusts the brightness (whiteness) of the imageRESETDefaults to factory settingsLAMP CHANGERChange to spare lampSPARE LAMPSpare lamp indicatorON/OFFActivity indicator 

USER GUIDELCD PROJECTOR17 6.5 CONNECTORS
All connectors are positioned on the left hand side of the LCD projector
(seen from the rear). See the technical data section for pinouts of the
various connectors.MOUSECOMPUTER
VIDEOS-VIDEOAUDIO
S-VIDEOVIDEO
MICSPEAKERS COMPUTER
Do not connect any other devices with similar plugs to the connectors of
the LCD projector, as this voids any warranty and may cause permanent
damage to the device.
CONNECTORFUNCTION MOUSEUniversal mouse connectorCOMPUTERCombined...

USER GUIDELCD PROJECTOR18 7 FEATURES
The LCD projector has a variety of different features implemented. This
chapter explains each feature in detail.
7.1.1 INTELLIGENT SAFECOOL SYSTEM
The fan operates as long as the LCD projector is switched on. This
ensures a continuous protection against high temperature inside the
projector. The cooling system is designed to minimize stray light and
noise.
7.1.2 MOTORIZED LAMP CHANGER
The projector is equipped with two 400W halogen lamps. If one lamp fails
during a...

USER GUIDELCD PROJECTOR19 Most settings are stored individually for each mode, including contrast,
brightness, tune etc. See the remote control table in the Remote Control
section.