Apple xserve slot load User Manual
Have a look at the manual Apple xserve slot load User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Xserve Take Apart - 49 Front Buttons, Xserve (Slot Load) and Xserve (Cluster Node) Procedure 1. Holding the power button by the plastic tab, lift straight up and remove the button from the front bezel. 2. Repeat for the system ID button. Note: Take care in handling the buttons. The face of each button is loosely attached to the button LEDs and can easily separate. Replacement Note: Position the replacement buttons in the front bezel as illustrated.
50 - Xserve Take Apart Front Panel Board, Xserve Front Panel Board, Xserve Tools No tools are required for this procedure. Preliminary Steps Before you begin, do the following: ¥ Open the server and place the bottom housing on a sturdy, flat surface. ¥ Remove the locking mechanism. Part Location
Xserve Take Apart - 51 Front Panel Board, Xserve Procedure 1. Disconnect the FireWire and front panel board cables from the board. 2. Lift the board out of the server.
52 - Xserve Take Apart Front Panel Board, Xserve (Slot Load) and Xserve (Cluster Node) Front Panel Board, Xserve (Slot Load) and Xserve (Cluster Node) Tools The only tool required for this procedure is a Phillips screwdriver. Preliminary Steps Before you begin, do the following: ¥ Open the server and place the bottom housing on a sturdy, flat surface. ¥ Remove the locking mechanism. ¥ Remove the front bezel. Part Location
Xserve Take Apart - 53 Front Panel Board, Xserve (Slot Load) and Xserve (Cluster Node) Procedure 1. Disconnect the FireWire and front panel board cables from the board. 2. Remove the two screws that mount the front panel board to the chassis. 3. Slide the board back and remove it from the server. Important: When replacing the front panel board, make sure the board slides under the black plastic cover of the light pipe.
54 - Xserve Take Apart Light Pipe, Xserve Light Pipe, Xserve Tools No tools are required for this procedure. Preliminary Steps Before you begin, open the server and place the bottom housing on a sturdy, ßat surface. Part Location
Xserve Take Apart - 55 Light Pipe, Xserve Procedure 1. Release the two clips on the sides of the front panel board, and pull the board back approximately 1.5 inches from the front of the server. 2. Remove the light pipe from the server. Replacement Note: When repositioning the light pipe against the inside front of the bezel, make sure the projections on the light pipe Þt into the holes in the bezel. Then slide the panel board forward until it Þts against the light pipe. Note: You may need to lift the light pipe slightly while sliding the front panel board, so that it doesnÕt catch the edge of the light pipe.
56 - Xserve Take Apart Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node) Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node) Tools The following tools are required for this procedure: ¥ Phillips screwdriver ¥ flat-blade screwdriver Preliminary Steps Before you begin, do the following: ¥ Open the server and place the bottom housing on a sturdy, flat surface. ¥ Remove the front bezel. Part Location
Xserve Take Apart - 57 Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node) Procedure 1. Using a ßat-blade screwdriver, ease Þrst one side and then the other side of the light pipe assembly from its opening in the front of the enclosure. 2. Remove the light pipe assembly from the server. Replacement Procedure 1. Remove the bottom row of light pipes from the light pipe assembly and insert them into the bottom row of light pipe holes in the front bezel.
58 - Xserve Take Apart
Light Pipe, Xserve (Slot Load) and Xserve (Cluster Node) 2. Insert the rest of the light pipe assembly into its opening in the front of the enclosure.
3. Replace the front bezel on the server, matching ports/projections with openings.
4. Replace the screw that secures the top of the bezel to the server.
5. Replace the two bezel brackets and their mounting screws.