Apple xserve late 2006 User Manual

							Xserve (Late 2006) Take Apart — Processor 101
Carefully lift the processor out of the holder.
 
3. 
Important: When removing or installing a processor, always hold the processor by three 
corners. Be extremely careful not to touch the gold pins on the bottom of the processor, as 
this type of connector is very sensitive to contamination. Also be careful not to touch the 
gold pins in the processor socket on the logic board.   
						

							Xserve (Late 2006) Take Apart — Processor 102
Replacing the Processor
Note: You will need to apply new thermal grease to the top of the replacement processor before 
installing it on the logic board. Steps 1 and 2 below explain how to apply the thermal grease.Using the syringe of thermal grease that came with the replacement processor, apply the 
1.  
entire contents of the syringe (approximately 4.5 cc) to the top surface of the processor.  
Important: Be sure not to get grease anywhere on the processor other than the very top, flat 
surface that directly contacts the heat sink.  
Use the edge of the package that the alcohol wipe came in as a spatula to spread the 
2.  
thermal grease evenly over the entire top surface of the processor. Scrape off any excess 
grease with the package edge, then discard the package.   
						

							Xserve (Late 2006) Take Apart — Processor 103
Holding the processor by three corners only, keep the processor level as you place it into its 
3. 
holder on the logic board, being careful not to get any thermal grease on the contacts of 
either the processor or its socket holder.
 
  
						

							Xserve (Late 2006) Take Apart — Processor 104
Note: When installing the processor on the logic board, align the processor notch with the 
tab on the processor holder, as shown. Then lower the processor straight down onto the 
socket.
 
Rotate the top of the holder to the closed position.
4.  
Engage the latch on the processor holder.
5. 
Repeat the steps above for the second processor.
6.   
						

							Xserve (Late 2006) Take Apart — Video Mezzanine Card 105
Video Mezzanine Card
Tools
The only tool required for this procedure is a Phillips #1 screwdriver.
Preliminary Steps
Before you begin, do the following:Open the Xserve and place the bottom housing on a sturdy, flat surface.
• 
Remove the right PCI-E riser card and any installed expansion card in slot 2
•  .
Part Location 
						

							Xserve (Late 2006) Take Apart — Video Mezzanine Card 106
Procedure
Remove the four Phillips screws that fasten the mezzanine card to the logic board.
1.  
Pull up evenly on all sides of the card to disconnect it from its logic board connector under 
2.  
the card, and remove the card from the Xserve.
Replacement Note: When installing the mezzanine card, be sure to press down gently and 
evenly on it to seat the connector on the underside of the card to the logic board. Then replace 
the four screws , and secure them in the order shown above. 
						

							Xserve (Late 2006) Take Apart — Logic Board 107
Logic Board
Tools
No tools are required for this procedure. You may, however, find a Phillips screwdriver useful in 
releasing the logic board thumbscrews.
Preliminary Steps
Before you begin, open the Xserve; place the bottom housing on a sturdy, flat surface; and 
remove the following:
Both power supplies
• 
PCI riser cards and any expansion cards in both slots
• 
FB-DIMM memory (remove only if you are installing a replacement logic board)
• 
Airflow duct
• 
Fan array
• 
Backplane-to-logic board I/O cable
• 
Both processor heat sinks
• 
Both processors (remove only if you are installing a replacement logic board)
• 
Video mezzanine card (remove only if you are installing a replacement logic board)
• 
Note: The replacement logic board does not include the processors, video mezzanine board, 
memory DIMMs, PCI riser cards, or expansion cards. You must transfer these modules from the 
original board to the new one.
Caution: Be careful not to flex the logic board or handle it by its components or heat sinks, which 
could damage the board or its components. To minimize flexing, always grasp the logic board 
only by its thumbscrews or edges when removing or installing it. 
						

							Xserve (Late 2006) Take Apart — Logic Board 108
Part Location
Caution: Although the logic boards for Xserve (Late 2006) and Xserve (Early 2008) are a 
similar size, do not install an older logic board in the Xserve (Early 2008) server.  
						

							Xserve (Late 2006) Take Apart — Logic Board 109
Removal Procedure
Study the next four images for properly moving the logic board before continuing with the 
1.  
steps. 
Caution: When removing and installing the logic board, be careful not to flex the logic board, 
which could damage the board or its components. To best distribute the weight of the logic 
board and minimize flexing, grasp the logic board only at the side and the end of the expansion 
card riser, as shown. 
						

							Xserve (Late 2006) Take Apart — Logic Board 11 0
Caution: When transferring the logic board, be careful not to flex the logic board, which could 
damage the board or its components. To best distribute the weight of the logic board and 
minimize flexing, hold the logic board at the long sides near the center, as shown.