Apple powerbook firewire User Manual

							 
Exploded View 
PowerBook (FireWire)
4 
PowerBook (FireWire) Screw Locator 
PowerBook (FireWire) Screw Locator
See Display 
Exploded View
Cardcage
1
23
7
7
7
6
7
41
2
4 3
5
10
11
12
12
 
Heat Exchanger to MPU
MPU EMI Shield (2) PCMCIA Card Cage
(2) PCMCIA Card Cage
(1) Modem EMI Filter
(2) LB near backup Battery and
     PCMCIA Cardcage
(1) Top Case under Clutch Cover
(3) Top Case to Stiffener, 
(1) Top Case to Stiffener near 
     Expansion bay
(1) Modem/airport cable holder
(5) Bottom Case up, (short)
(1) Yoke
(1)Heat Exchange/ Modem,
     to bottom case 
(4) Hard Drive Bracket 
      to Hard Drive

 [Logic Board By Fan
(4) I/O Door
7
6
(2) Power Supply Card

 (2) Bottom Case, Long Screws (1) Logic Board 
(upper left Corner)
Bottom Case 
  
PCMCIA 
Cardcage
I/O Logic
Board
Yoke
Modem EMI Filter
Stiffener
Power
Supply
Card 
 Top Case
Modem
Wireless
Antenna
Holder
Heat 
Exchanger
Hard Drive
Bracket
Microprocessor
EMI Shield10
8
8
9
9
11
11
7
13
14
15
(4) LCD Panel to Braces
(2) Antenna ,Right Side
(6) Bezel
(4) Display Clutches
(4) Display Braces Display 
						

							 
Exploded View 
PowerBook (FireWire)
5 
PowerBook (FireWire) Display Screw Locator 
PowerBook (FireWire) Display Screw Locator
Screw Cover 
922-3823 Clutch/
Brace,
Wire 
Side 
Display 
Housing
14.1 Display
 
Clutch/
Brace,
Flex
Side 
Display Bezel 
Bumper	
922-3824
Wireless 
Cable Antenna
13
13
13
13
13
14 
14
15
15
15
15
15
15
15
(4) LCD Panel to Braces
(2) Antenna ,Right Side
(6) Bezel
(4) Display Clutches
(4) Display Braces Display 
						

							 
Exploded View 
PowerBook (FireWire)
6 
PowerBook (FireWire) Reassembly Checksheet 
PowerBook (FireWire) Reassembly Checksheet
  1   Install backup battery (do not connect cable yet).
  2   Install PCMCIA cardcage on I/O logic board (4 screws: 2 short, 2 long).
  3   Install reset button on I/O logic board.
  4   Install RJ-11 cable/phone jack on I/O logic board.
  5   Install sound card on I/O logic board.
  6   Install I/O logic board on bottom case.
  7   Install fan on bottom case.
  8   Install modem EMI filter card on stiffener (1 screw).
  9   Install stiffener (2 screws).
10   Install screw on I/O logic board near fan.
11   Install nut on back left corner of I/O logic board.
12   Install yoke (1 screw and 1 spring).
13   Install power supply card (2 screws in middle of card).
14   Install I/O EMI shield.  
1
23 4
5
Long 
ScrewsShort
 Screws
108
6
12 14
79
Underside of 
I/O Logic Board
11
Reset 
Button
RJ11
Cable/
Phone
JackModem
FilterScrew
13 
						

							 
Exploded View 
PowerBook (FireWire)
7 
PowerBook (FireWire) Reassembly Checksheet 
PowerBook (FireWire) Reassembly Checksheet (continued)
37
30
30
32
32
31
UndersideLong LongConnectors Screw
15   Snap top case to bottom case.
16   Connect power and speaker cables 
       to I/O logic board.
17   Connect wireless card slot cable to I/O logic board.
18   Install power supply card (2 screws on top of card).
19   Connect trackpad cable to I/O logic board.
20   Tuck power supply card EMI shield under palmrest.
21   Install right stiffener screw.
22   Install screws under clutch cover (4).
23   Install bottom case screws on underside of unit
       (5 short, and 2 long over expansion bay 
       release levers).
24   Connect modem EMI filter board cable to modem
       and install modem on I/O logic board (1 screw).
25   Install wireless antenna cable holder (1 screw).
26   Install and connect hard drive to I/O logic board.
27   Install display (4 screws behind I/O door).28   Install AirPort card (if present).
29   Route wireless antenna cable and connect it
       to AirPort card or into holder near modem. 
30   Connect display cable to I/O logic board
        and install screw.
31   Connect backlight cable to inverter board 
       and install inverter board on top case.
32   Connect inverter board cable to 
       I/O logic board and route cable.
33   Install clutch cover.
34   Install microprocessor board and 
       heat exchanger (1 screw).
35   Connect backup battery cable to 
       I/O logic board.
36   Install microprocessor EMI shield (2 screws).
37   Install and connect keyboard.  
38   Install expansion bay modules.
24
26
18
38
29
35
21
31
36
26
16
27
20
34
38
37
17
19
24
22
28
27
38
15
25
23