Apple macbook pro User Manual

MacBook Pro Basics— General Information 11
IR and the Apple Remote
Infrared port is placed on the front of the unit just to the right of the display latch button. This 
port is used in conjunction with the Apple Remote provided with each unit. It can be used to 
control Front Row software that manages your music, photos and videos. The remote can also be 
used to control other applications as well.
 
iSight Camera
An iSight Camera has been built-in into the display bezel. It allows a user to capture...

MacBook Pro Basics— General Information 12
Identifying the MacBook Pro
Below are views of the MacBook Pro, with identifying features.
Left side: MagSafe™ magnetic power connector.
Right side: No FireWire 800 port.
Front: Infrared sensor window.
Rear: Grey antenna window in the clutch cover.
Display bezel: MacBook Pro. 

MacBook Pro Basics— General Information 13
Serial Number and Ethernet ID
The Serial Number and Ethernet ID are located in the battery bay. 
Tools
This procedure requires the following tools: Clean non-marring work surface
• 
ESD wrist strap and mat
• 
Multi-compartment screw tray (such as a plastic ice cube tray)
• 
#0 Phillips screwdriver (magnetized)
• 
#1 Phillips screwdriver (magnetized)
• 
Torx T6 screwdriver (magnetized)
• 
4 mm socket wrench
• 
Black stick (nylon probe 922-5065) (or other...

MacBook Pro Basics— General Information 14
Electrostatic Discharge (ESD)
Use a properly grounded ESD wrist strap and mat when working on the inside of the computer.
Service Manual Note
In this manual, graphics or photos are intended to help illustrate procedures or information only, 
and may show different levels of disassembly, board colors, configurations, or computer models, 
than your computer.
Kapton® Tape Note
Kapton tape is used to secure cables and connectors where necessary.
During disassembly,...

 Service Source
© 2006 Apple Computer, Inc. All rights reserved.
Take Apart
MacBook Pro 

MacBook Pro Take Apart — Foot 16
Foot
Tools
This procedure requires the following tools:Foot kit
• 
Tweezers or needlenose pliers
• 
Soft cloth
• 
Preliminary Step
Before you begin, check the foot location that needs replacement and verify that the case plug is 
attached. Also verify that the case plug, and the case foot in the kit, match the pictures below.
Plug Area on Bottom Case Matching FootAction
Missing case plug Not available for replacementReplace the bottom case, or 
send to Apple Repair...

MacBook Pro Take Apart — Foot 17
Procedure
Warning: The glue used in this procedure can bond instantly to skin. Do not touch the glue. 
In the event of contact, review the safety instructions at the end of this document. For 
additional information, refer to the glue manufacturer:Elmer’s Products, Inc.
Columbus, OH. 43215-3799
www.krazyglue.com
Place the computer upside down on a clean, lint-free cloth or other nonabrasive surface.
1.  
Select a foot from the kit. Verify that the case plug and case foot...

MacBook Pro Take Apart — Foot 18
 
4.   Warning: GLUE IS AN EYE AND SKIN IRRITANT. BONDS SKIN INSTANTLY. Do not touch the 
glue at any time. Before opening the glue, review the safety instructions at the end of 
this document.  
Important: The glue tube included in the kit is sealed until first use. Do not break the seal 
until you are ready to use the glue. To break the seal, hold the tube upright and away from 
you. Place the hollow nozzle cap on the tube and tighten it all the way down. The tube is...

MacBook Pro Take Apart — Battery 19
Battery
Tools
This procedure requires the following tools: Clean non-marring work surface
• 
Preliminary Steps
Warning: Always shut down the computer before opening it to avoid damaging its internal 
components or causing injury. After you shut down the computer, the internal components 
can be very hot. Let the computer cool down before continuing.
Part Location 

MacBook Pro Take Apart — Battery 20
Procedure
Warning: If the computer has been recently operating, allow it to cool down before 
performing this procedure.Shut down the computer.
1.  
Disconnect the power cord and any other cables connected to the computer.
2.  
Place the computer face down.
3. 
Slide both battery latches away and lift the battery out of the battery bay.
4.