Apple macbook pro 17 inch late 2008 User Manual

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Memory 21
Procedure
Warning: If the computer has been recently operating, allow it to cool down before 
performing this procedure.Place the computer upside down.
1.  
Remove four screws from the memory door.  
2.  
Remove the door, as shown.  
3. 
 
Notes:  
•  If only one memory card is installed, the factory installs it in the bottom memory slot.  
•  Memory must be removed from the top slot before removing from the bottom slot. 

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Memory 22
To remove memory cards, carefully spread the two locking tabs for the slot (top or bottom) 
4.  
away from the card on both sides and allow the card to pop up slightly.  
Pull the card straight back and out of the memory slot. Handle the memory card by the 
5. 
edges only, taking care not to touch the gold contacts.   

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Memory 23
Replacement Procedure
Notes: DDR memory cards do not fit in this slot, only DDR2 (different notch location).
• 
If installing two cards, install into the bottom slot first. 
• 
Align the notch in the memory card with the tooth in the slot before inserting.
• 
To install memory cards, insert them at a 30-degree angle. 
1.   Note: Insert the bottom card 
behind the locking tabs of the top slot.  
Firmly push the card...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Memory 24
Verify that the card is fully seated by pushing firmly with your thumbs. 
4.  
Check that the cards are secured by the brackets on both sides.
5. 
Install the memory door.
6.  
Replace the battery.
7.  
Use Apple System Profiler to verify that the memory is recognized. (Choose the menu 
8.  
bar Apple logo () > About This Mac, click More Info..., select the System Profile tab, 
open the Memory Overview.)
NOTE: The...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Top Case 25
Top Case
Tools
This procedure requires the following tools: #0 Phillips screwdriver (magnetized)
• 
Torx T6 screwdriver (magnetized)
• 
Black stick (nylon probe 922-5065) or other non-conductive nylon or plastic flat-blade tool
• 
Multi-compartment screw tray (such as a plastic ice cube tray)
• 
Preliminary Steps
Before you begin, remove the following:
•  Batter y
Memor
•  y
Part Location 

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Top Case 26
Procedure
Notes: This procedure removes the top case and keyboard assembly. The keyboard is removable 
• 
only after removing the top case.
Place the computer upside down.
1.  
2.   Remove the nine screws shown. 
3.  Remove the four screws from each side.
 
Remove the two screws from the back edge.
4.  
. 

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Top Case 27
Face the computer toward you with the display open slightly past 90-degrees. Using your 
5. 
fingernails or the tips of your fingers, grasp just beneath the back edge of the top case 
behind the keyboard or in the upper right and left corners. Lift upward a few inches, then 
work your hands around the top case toward the front, slowly lifting and encouraging the 
clips and screw tabs to release. A snapping noise when...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Top Case 28
Note: Take care to preserve the cosmetic integrity of the plastic beading around the edges of the 
top case. If using a black stick for leverage to get the clips to release, don’t rotate the stick too 
vigorously along the edges to avoid denting the soft plastic. 
Along the front, start at the left and slowly encourage the snaps and screw tabs (shown in 
6.  
graphic below) to release as you move right. A snapping noise...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Top Case 29
Important: To avoid bending screw tabs along the back edge of the top case, lift the top case 
slightly so that it does NOT touch the bottom case, then rotate the front of the case up and back 
until you can disconnect the keyboard flex cable from the logic board.
 
  

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Top Case 30
Replacement Procedure
Note: If replacing the top case, remove the Keyboard and transfer to the replacement top case.
Visually check to verify that all cables are connected and routed correctly with nothing raised 
1.  
up or incorrectly over a component. 
Check perimeter wiring and cables around clutches to verify that they will not be caught or 
2.  
pinched by the top case during replacement.
On the computer, verify...