Apple macbook pro 17 inch 2 4ghz User Manual

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Backup Battery 91
Procedure
(a) For the MacBook Pro (17-inch), use a needlepoint probe to disconnect the cable 
1.  
connector from the logic board, as shown below. Warning: When using a needlepoint probe, 
great care must be used to avoid slipping off the connector and damaging components.
 
(b) For the MacBook Pro (17-inch Core 2 Duo, 2.4GHz and Early 2008), sandwich the 
connector between a finger or thumb on top and a black...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Backup Battery 92
Pry up the backup battery from the well in the right speaker.
 
2.  
To install a replacement backup battery, remove the adhesive protector and press the 
3. 
battery into place in the same well that it was removed from the right speaker.
Guide its cable into the channel along the right speaker.
4.  
Connect the cable to the logic board. 
5. 
Note 1: The MacBook Pro (17-inch) connector is keyed to install only one...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Backup Battery 93
JST Connectors
To disconnect a JST connector, sandwich the connector firmly between a finger on top and a 
1.  
black stick under the cabling next to the connector, then lift (as in the animation below).
1.   
To reseat or reconnect a JST connector, use a black stick or your finger to snap it into place, 
2.  
making sure the connector sits perfectly flat and flush with the sides of the connector well. 

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Backup Battery 94
Note: Given a very keen eye, one way to distinguish the right side up of a JST connector is by 
looking for the word ‘push’ on the top side of the connector, as shown below. 

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Ambient Light Sensors 95
Ambient Light Sensors
Tools
This procedure requires the following tools: Torx T6 screwdriver (magnetized)
• 
Preliminary Steps
Before you begin, remove the following:
Batter
•  y
Top Cas
•  e
Part Location 

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Ambient Light Sensors 96
Procedure
The right ambient light sensor is part of the logic board and is not separately replaceable, but 
has a removable dust cover that attaches with a small screw to the right speaker. 
The left ambient light sensor is part of the left I/O board and is not separately replaceable, and 
has a dust cover glued onto the left speaker that is also not separately replaceable.
To remove the right sensor’s dust...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Speakers 97
Speakers and Microphone
The right and left speakers are two separately replaceable parts.
The left speaker also contains a separately replaceable microphone.
Tools
This procedure requires the following tools: Torx T6 screwdriver (magnetized)
• 
Black stick (nylon probe 922-5065) or other non-conductive nylon or plastic flat-blade tool
• 
Kapton tape (922-1731) (0.5-inch x 12-yard roll)
• 
Preliminary Steps
Before you...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Speakers 98
Procedure
To remove the microphone: 
Note: The microphone does NOT have to be removed from the left speaker if not replacing the 
microphone or speaker.
Note: Some photo details below may differ slightly from the model of 17-inch MacBook Pro you 
are repairing; however, the procedure itself remains consistent for any of the models.Use the flat end of a black stick to pry the microphone boot out of its well in the left...

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Speakers 99
To remove the left speaker: 
Lift the antenna wires out of the channel along the right side of the speaker. 
1.  
Remove two screws.  
2.   

MacBook Pro 17-inch (original, Core 2 Duo, 2.4/2.6GHz, 2008) Take Apart — Speakers 10 0
Disconnect the speaker cable and the microphone cable, and lift out the speaker.
 
3. 
Replacement Notes: 
Verify that the antenna cables lay flat within the channel along the edge of the speaker.  
•