Apple mac pro User Manual

Mac Pro Take Apart — Memory (DIMMs) and Memory Riser Cards 21
Procedure
Holding the memory riser card by the two finger holes, pull it out of the memory cage and 1. 
place the card DIMM side up on a soft, clean cloth. 
Open the ejectors on the DIMM slot by pushing them out to the sides, and remove the 2.  
DIMM from the riser card.  

Mac Pro Take Apart — Memory (DIMMs) and Memory Riser Cards 22
Replacement Note: Align the DIMM in the slot on the riser card and push both ends of the 
DIMM down until the ejectors snap back up into place.
Warning: FB-DIMMs carry heatsinks on either side of the DIMM. Never attempt to remove the 
heatsinks from the DIMMs. Doing so could damage the DIMM. 

Mac Pro Take Apart — PCI Express/Graphics Card 23
PCI Express/Graphics Card
The Mac Pro logic board includes one double-wide PCI Express graphics slot and three PCI 
Express expansion slots, for a total of four slots. The computer comes with a graphics card 
installed in slot 1. You can install additional PCI Express graphics and expansion cards in the 
remaining three PCI Express expansion slots.
Important:  Graphics cards from previous Power Mac G5 models are not compatible with Mac 
Pro models. In...

Mac Pro Take Apart — PCI Express/Graphics Card 24
Preliminary Steps
Before you begin, open the computer, and lay it on its side with the access side facing up.
Note: You may also find it helpful to remove the hard drives and carriers and any adjacent PCI 
Express cards before beginning this procedure.
Part Location 

Mac Pro Take Apart — PCI Express/Graphics Card 25
Procedure
This procedure explains how to remove a standard card and a card that includes a booster cable. 
Before you can remove either type of card, however, you must first loosen the two captive screws 
that secure the PCI bracket to the enclosure and remove the bracket. 
Warning: When removing or installing a card, handle it only by the edges. Do not touch its 
connectors or any of the components on the card. Lift the card straight out from the...

Mac Pro Take Apart — PCI Express/Graphics Card 26
Standard Card
Release the small locking clip at the front of the card’s logic board connector by pushing the 1. 
clip up toward the media shelf.
Holding the card by the top corners, pull up the card and remove it from its expansion slot.2.  
Replacement Note: Align the card’s connector with the expansion slot and press until the 
connector is inserted all the way into the slot. If you’re installing a 12-inch card, make sure the 
card engages the...

Mac Pro Take Apart — PCI Express/Graphics Card 27
Card with Booster Cable
Disconnect the booster cable from the logic board.1. 
Release the small locking clip at the front of the card’s logic board connector by pushing the 2.  
clip up toward the media shelf.
Holding the card by the top corners, gently pull up the card and remove it from its 3. 
expansion slot. 
If you are replacing the booster cable with a new booster cable, disconnect the cable from 4. 
the card. 

Mac Pro Take Apart — PCI Express/Graphics Card 28
Replacement Note: There are two logic board connectors for booster cables. Connect the 
booster cable for a card in PCI slot 1 to the lower connector. Connect the booster cable for a card 
in PCI slot 2 to the upper connector. 

Mac Pro Take Apart — Power Supply 29
Power Supply
Tools
The only tool required for this procedure is a magnetized 2.5 mm hex wrench. You may also find 
a flat-blade screwdriver helpful in releasing some cable connectors.
Preliminary Steps
Before you begin, open the computer, lay it on its side with the access side facing up, and remove 
the following:
Hard drives and hard drive carriers in drive bays 3 and • 4
Optical drive carrier and optical drive• s
Any PCI Express cards that block access to the power...

Mac Pro Take Apart — Power Supply 30
Procedure
Removing the Power Supply
Using a magnetized 2.5 mm hex wrench remove the four power supply mounting screws 1. 
from the bottom of the media shelf. 
Depress the upper right corner of the power supply and slide the power supply toward the 2.  
front of the computer.