Apple mac pro User Manual

 Service Source
© 2006 Apple Computer, Inc. All rights reserved.
Upgrades
Mac Pro 

Mac Pro Upgrades — AirPort Extreme Card 162
AirPort Extreme Card
Important: The computer enclosure includes AirPort antenna wires and a Bluetooth antenna 
wire. The Bluetooth antenna wire looks similar to the AirPort antenna wires, except that it 
includes a “BT” label. For proper operation, be careful not to connect the Bluetooth antenna wire 
to the AirPort card or any AirPort antenna wire to the Bluetooth card. 
Note: You may connect the AirPort antenna wires to either AirPort card connector.
Tools...

Mac Pro Upgrades — AirPort Extreme Card 16 3
Procedure
Connect the AirPort antenna wires to the connectors on the card. 1. 
Important: Be sure to connect the wires that are marked 1 and 3 to the card; the antenna 
wire that is marked 2 should be taped out of the way. 
Insert the AirPort Extreme card into its logic board connector at an angle, as illustrated. Then 2.  
lower the screw end of the card down to the standoffs on the logic board.  

Mac Pro Upgrades — AirPort Extreme Card 16 4
Install the two AirPort Extreme card mounting screws.3.   

Mac Pro Upgrades — Bluetooth Card 165
Bluetooth Card 
Important: The computer enclosure includes one Bluetooth antenna wire, which looks similar 
to the AirPort antenna wires, except that it includes a “BT” label. For proper operation, be careful 
not to connect the Bluetooth antenna wire to the AirPort card or any AirPort antenna wire to the 
Bluetooth card. 
Tools
The only tool required for this procedure is a magnetized jewelers Phillips #1 screwdriver.
Preliminary Steps
Before you begin, open the...

Mac Pro Upgrades — Bluetooth Card 166
Procedure
Connect the Bluetooth antenna wire to the connector on the Bluetooth card. 1. 
Lower the card onto the Bluetooth connector on the logic board.2.  
Install the two Bluetooth card mounting screws. 3.  

Mac Pro Upgrades — PCI Express/Graphics Card 16 7
PCI Express/Graphics Card
The Mac Pro logic board includes one double-wide PCI Express graphics slot and three PCI 
Express expansion slots, for a total of four slots. The computer comes with a graphics card 
installed in slot 1. You can install additional PCI Express graphics and expansion cards in the 
remaining three PCI Express expansion slots.
Important: Combined maximum power consumption for all four PCI Express slots must not 
exceed 300 W.
Slot 1:...

Mac Pro Upgrades — PCI Express/Graphics Card 168
Part Location
Procedure
This procedure explains how to install a standard card and a card that includes a booster cable. 
Before you can install either type of card, however, you must first loosen the two captive screws 
that secure the PCI bracket to the enclosure and remove the bracket. You must also remove the 
port cover for the PCI slot where you are installing the new card.  

Mac Pro Upgrades — PCI Express/Graphics Card 16 9
Warning: When installing or removing a card, handle it only by the edges. Do not touch its 
connectors or any of the components on the card. 
Standard Card
Align the card’s connector with the expansion slot and press until the connector is inserted 1. 
all the way into the slot. If you’re installing a 12-inch card, make sure the card engages the 
appropriate slot in the PCI card guide. 
• Don’t rock the card from side to side; instead, press the card...

Mac Pro Upgrades — PCI Express/Graphics Card 170
Card with Booster Cable
Connect the booster cable to the card. 1. 
Holding the card by the top corners, insert it straight down into its expansion slot. 2.  
Connect the booster cable to the logic board. 3. 
Note: There are two logic board connectors for booster cables. Connect the booster cable for 
a card in PCI slot 1 to the connector that is closest to the heatsink cover. Connect the booster 
cable for a card in PCI slot 2 to the connector closest to...