Apple mac pro early 2008 User Manual
Have a look at the manual Apple mac pro early 2008 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Mac Pro (Early 2008) Take Apart — AirPort Antenna Board with Cables 121 Tilt the antenna board away from the back panel a short distance.6. Feed each antenna cable separately out through the small opening in the bottom panel. 7. Remove the antenna board and cables from the enclosure.8.
Mac Pro (Early 2008) Take Apart — Optical Drive Power Cable 12 2 Optical Drive Power Cable Tools The only tool required for this procedure is a magnetized #1 Phillips screwdriver. Preliminary Steps Before you begin, open the computer, lay it on its side with the access side facing up, and remove the following: Optical drive carrier and optical drive• s H• ard drives and hard drive carriers in drive bays 1 and 2 Any 12-inch • PCI Express cards Processor heatsink cove• r Front fan assembl• y Part Location
Mac Pro (Early 2008) Take Apart — Optical Drive Power Cable 12 3 Procedure Using a magnetized #1 Phillips screwdriver, remove the two mounting screws on the hard 1. drive connector for drive bay 1 and move the connector out of the way. Unwind the tape that holds the optical drive data cable to the optical drive power cable.2. Disconnect the optical drive power cable from the logic board.3. Insert the logic board end of the power cable into the opening in the media shelf at hard 4. drive bay 1 and remove the cable from the enclosure.
Mac Pro (Early 2008) Take Apart — Optical Drive Power Cable 12 4
Mac Pro (Early 2008) Take Apart — Optical Drive Data (Ribbon) Cable 12 5 Optical Drive Data (Ribbon) Cable Tools The only tool required for this procedure is a magnetized #1 Phillips screwdriver. Preliminary Steps Before you begin, open the computer, lay it on its side with the access side facing up, and remove the following: Optical drive carrier and optical drive• s H• ard drives and hard drive carriers in drive bays 1 and 2 Any 12-inch • PCI Express cards Processor heatsink cove• r Front fan assembl• y Part Location
Mac Pro (Early 2008) Take Apart — Optical Drive Data (Ribbon) Cable 12 6 Procedure Using a magnetized #1 Phillips screwdriver, remove the two mounting screws on the hard 1. drive connector for drive bay 1 and move the connector out of the way. Unwind the tape that holds the optical drive data cable to the optical drive power cable.2. Disconnect the optical drive data cable from the logic board.3. Insert the cable into the opening in the media shelf at hard drive bay 1 and remove the 4. cable from the enclosure.
Mac Pro (Early 2008) Take Apart — Ambient Board 12 7 Ambient Board Note: The ambient board is attached to the enclosure with adhesive. Once you remove the ambient board, you may have to apply new adhesive before reattaching the same ambient board. Replacement ambient boards come with adhesive already in place. Tools The only tools required for this procedure are a jeweler’s flat-blade screwdriver. Preliminary Steps Before you begin, open the computer, lay it on its side with the access side facing up, and remove the optical drive carrier and optical drives. Part Location
Mac Pro (Early 2008) Take Apart — Ambient Board 12 8 Procedure Locate the ambient board on the inside left corner of the top panel, above the optical drive 1. carrier. Disconnect the ambient board cable from the ambient board.2. Using a jeweler’s flat-blade screwdriver, carefully pry the board from the enclosure. 3. Important: After you replace the ambient board, you must reset the System Management Controller. Refer to “Resetting the Logic Board” in the Troubleshooting chapter.
Mac Pro (Early 2008) Take Apart — Ambient Board Cable 129 Ambient Board Cable Tools The only tool required for this procedure is a magnetized #1 Phillips screwdriver. Preliminary Steps Before you begin, open the computer, lay it on its side with the access side facing up, and remove the following: Optical drive carrier and optical drive• s H• ard drives and hard drive carriers in drive bays 1 and 2 Any 12-inch • PCI Express cards Processor heatsink cove• r Front fan assembl• y Part Location
Mac Pro (Early 2008) Take Apart — Ambient Board Cable 130 Procedure Remove any tape holding the ambient board cable to the enclosure.1. Disconnect the ambient board cable from the ambient board and logic board. 2. Using a magnetized #1 Phillips screwdriver, remove the two mounting screws on the hard 3. drive connector for drive bay 1 and move the connector out of the way. Route the ambient board cable out through the opening in the media shelf and remove the 4. cable from the enclosure. Important: After you replace the ambient board cable, you must reset the System Management Controller. Refer to “Resetting the Logic Board” in the Troubleshooting chapter.