Apple imac 20 inch mid 2009 User Manual
Here you can view all the pages of manual Apple imac 20 inch mid 2009 User Manual. The Apple manuals for Display are available online for free. You can easily download all the documents as PDF.
Page 171
iMac (20-inch, Early/Mid 2009) Take Apart — Mechanism 171 2010-11-24 Removal 1 Remove T10 screws: (4) 922-8849 2 Peel back EMI mesh tape on mechanism. 3 Lift mechanism off chassis.
Page 172
iMac (20-inch, Early/Mid 2009) Take Apart — Chassis 172 2010-11-24 First Steps Remove: • Access Door • Glass Panel • Front Bezel • LCD Panel • Right Speaker • Logic Board • Power Supply • Hard Drive • Hard Drive Fan • Hard Drive Data Cable • Optical Drive • Optical Drive Fan • Mechanism Cover • Stand Tools • ESD wrist strap • Torx T10 screwdriver Chassis
Page 173
iMac (20-inch, Early/Mid 2009) Take Apart — Chassis 173 2010-11-24 Removal 1 Slide AC connector out from under the pressure wall. The pressure wall does not need to be removed. 2 Remove T10 screws: (3) 922-8250, at top; slightly longer, slightly larger head (6) 922-6850 (1) 922-7069, ground Reassembly Note: Secure green/yellow grounding cable from AC inlet to chassis with short, stubby ground screw.
Page 174
iMac (20-inch, Early/Mid 2009) Take Apart — Chassis 174 2010-11-24 3 If mechanism is still installed, peel back EMI mesh tape on mechanism attached to rear housing. Note: Mechanism can stay attached to chassis if you removed them to get to lower modules. 4 Lift chassis out of rear housing. Reassembly Reassembly is an exact reversal of the steps, with two notes: 1 Make sure the DC power supply/ SATA/ inverter cable is properly routed in rear housing before replacing chassis. Position...
Page 175
iMac (20-inch, Early/Mid 2009) Take Apart — Cable, DC, Power Supply/SATA/Inverter 175 2010-11-24 First Steps Remove: • Access Door • Glass Panel • Front Bezel • LCD Panel • Right Speaker • Logic Board • Power Supply • Hard Drive • Hard Drive Fan • Hard Drive Data Cable • Optical Drive • Optical Drive Fan • Mechanism Cover • Stand • Chassis Tools • ESD wrist strap • Torx T10 screwdriver Cable, DC, Power Supply/SATA/Inverter
Page 176
iMac (20-inch, Early/Mid 2009) Take Apart — Cable, DC, Power Supply/SATA/Inverter 176 2010-11-24 Removal 1 Tape microphone cable to top of rear housing, to keep it out of the way 2 Disconnect inverter cable.
Page 177
iMac (20-inch, Early/Mid 2009) Take Apart — Cable, DC, Power Supply/SATA/Inverter 177 2010-11-24 3 Remove clear Kapton tape securing DC power cable to rear housing. 4 Remove T10 screw on cable guide in middle of rear housing: (1) 922-6800
Page 178
iMac (20-inch, Early/Mid 2009) Take Apart — Cable, DC, Power Supply/SATA/Inverter 178 2010-11-24 5 Before removing cable, note how it routes between black guideposts in rear housing. Reassembly 1 Install DC power cable into rear housing as shown above in removal step 5. 2 In top left corner of rear housing, position cable between black guideposts and secure cable with clear Kapton tape. Route inverter power cable off to the right.
Page 179
iMac (20-inch, Early/Mid 2009) Take Apart — Cable, DC, Power Supply/SATA/Inverter 179 2010-11-24 3 In the middle of rear housing, continue laying cable between black guideposts and secure cable with clear Kapton tape. 4 Position plastic cable guide (with foam) over the cable. 5 Replace T10 screw: (1) 922-6800 Note: Make sure cable guide is flush with rear housing. If cable guide is not seating properly, double check that cable is situated properly between black guideposts.
Page 180
iMac (20-inch, Early/Mid 2009) Take Apart — Cable, DC, Power Supply/SATA/Inverter 180 2010-11-24 6 Toward bottom of rear housing, continue laying cable between black guideposts and secure cable with clear Kapton tape. 7 Secure inverter cable to rear housing with clear Kapton tape. 8 Reconnect cable to inverter. 9 Continue with reassembly of chassis and other removed modules.