Home > Apple > Display > Apple imac 20 inch mid 2009 User Manual

Apple imac 20 inch mid 2009 User Manual

Here you can view all the pages of manual Apple imac 20 inch mid 2009 User Manual. The Apple manuals for Display are available online for free. You can easily download all the documents as PDF.

Page 111

iMac (20-inch, Early/Mid 2009) Take Apart — Front Bezel 111 2010-11-24
4 Unwrap any Kapton 
tape and disconnect 
microphone cable 
from cable extension 
at top of front bezel.
5 Lift front bezel off rear 
housing.
Reassembly Note:  Secure 
bottom part of front bezel 
first and then lower top 
part, the reverse of the 
action shown here.  

Page 112

iMac (20-inch, Early/Mid 2009) Take Apart — Camera 112 2010-11-24
First Steps
Remove:
• Access Door
•  Glass Panel
•  Front Bezel
Tools
• ESD wrist strap
•  Torx T10 screwdriver
Camera  

Page 113

iMac (20-inch, Early/Mid 2009) Take Apart — Camera 113 2010-11-24
Removal
1 
Remove T10 screws: 
(2) 922-8850
2 Lift camera bracket out 
of rear housing.
3 Unwrap Kapton tape 
covering camera cable 
and connector.
4 Disconnect camera 
cable from camera 
board.  

Page 114

iMac (20-inch, Early/Mid 2009) Take Apart — Battery 114 2010-11-24
First Steps
Remove:
• Access Door
•  Glass Panel
•  Front Bezel
Tools
• ESD wrist strap
•  Black stick
Battery  

Page 115

iMac (20-inch, Early/Mid 2009) Take Apart — Battery 115 2010-11-24
Removal
1 
Use a black stick to 
pry battery from 
battery socket on 
logic board.
Reassembly
1 
Make sure battery 
socket is open and 
free of dust.
2 Press battery (922-
8892) into socket with 
engraved markings (+ 
side) facing up.  

Page 116

iMac (20-inch, Early/Mid 2009) Take Apart — IR (Infrared) Board (Early 2009) 116 2010-11-24
First Steps
Remove:
• Access Door
•  Glass Panel
•  Front Bezel
Note: iMac (20-inch, Mid 
2009) model does not 
have an IR Board.
Tools
•  ESD wrist strap
•  Torx T6 screwdriver
IR (Infrared) Board 
(Early 2009)  

Page 117

iMac (20-inch, Early/Mid 2009) Take Apart — IR (Infrared) Board (Early 2009) 117 2010-11-24
Removal
1 
Remove T6 screws: 
(2) 922-8579
2 Disconnect IR cable 
(922-8832) from logic 
board.
3 Lift IR board and 
cable off logic board.
Replacement Note:  
If installing a new IR 
board, transfer IR cable 
from old board to new 
board.  

Page 118

iMac (20-inch, Early/Mid 2009) Take Apart — AirPort Extreme Card 118 2010-11-24
First Steps
Remove:
• Access Door
•  Glass Panel
•  Front Bezel
Tools
• ESD wrist strap
•  Torx T6 screwdriver
AirPort Extreme Card  

Page 119

iMac (20-inch, Early/Mid 2009) Take Apart — AirPort Extreme Card 119 2010-11-24
Removal
1 
Remove T6 screw: 
(1) 922-8579
2 Disconnect 2 antenna 
cables.
Note: The antenna cables 
and connectors are very 
delicate and should be 
carefully removed by 
pulling on the connector 
rather than the cable.  
If an antenna cable is 
damaged, replace rear 
housing.
Reassembly Note:  Either 
cable can be attached to 
either connector with no 
change in performance.
3 Hold AirPort card by 
edges and pull it out 
of...

Page 120

iMac (20-inch, Early/Mid 2009) Take Apart — Bluetooth Board (Early 2009) 120 2010-11-24
First Steps
Remove:
• Access Door
•  Glass Panel
•  Front Bezel
Note: iMac (20-inch, Mid 
2009) model does not 
have a Bluetooth Board.
Tools
•  ESD wrist strap
•  Torx T6 screwdriver
Bluetooth Board 
(Early 2009)  
Start reading Apple imac 20 inch mid 2009 User Manual

Related Manuals for Apple imac 20 inch mid 2009 User Manual

All Apple manuals