Apple imac 17 inch User Manual
Here you can view all the pages of manual Apple imac 17 inch User Manual. The Apple manuals for Display are available online for free. You can easily download all the documents as PDF.
Page 101
11. Insert the power supply insulators if you removed them. 98 iMac (Flat Panel) Take Apart Base Reassembly
Page 102
12. Replace the fan, the fans screws, and connect the fan cable. 13. Replace the optical drive door assembly. 14. Replace the door springs. Base Reassembly iMac (Flat Panel) Take Apart - 99
Page 103
15. Rotate the base so the optical door is on the right. Replace the power supply and the six screws. Remember, the two smaller screw locations are hidden under the optical door flap. 16. Attach the hard drive and optical drive to the drive carrier. 100 iMac (Flat Panel) Take Apart Base Reassembly
Page 104
17. Replace the optical/drive carrier assembly, EMI shield, and screws. 18. Replace the I/O port covers. Base Reassembly iMac (Flat Panel) Take Apart - 101
Page 105
19. Replace the battery and memory on the logic board. 20. Replace the blank white “plug” into the AC line filter hole in the bottom housing before reinstalling the AC line filter. Note: Newer models may have the plug built into the bottom housing. 21. Replace the AC line filter and screws. 22. Replace the antenna extension and the black insulator into the bottom housing 102 iMac (Flat Panel) Take Apart Base Reassembly
Page 106
![Page 106
23. Replace the modem filter board into the opening in the bottom housing.\
Replace the
modem and modem filter board screws. Connect the cable to the modem.
24. Replace the logic board and the logic board screws.
Base Reassembly iMac (Flat Panel) Take Apart -
103](http://img.usermanuals.tech/thumb/462/38776/w300_imac-17-inch-1ghz-105.png "Page 106
23. Replace the modem filter board into the opening in the bottom housing.\
Replace the
modem and modem filter board screws. Connect the cable to the modem.
24. Replace the logic board and the logic board screws.
Base Reassembly iMac (Flat Panel) Take Apart -
103")
23. Replace the modem filter board into the opening in the bottom housing.\ Replace the modem and modem filter board screws. Connect the cable to the modem. 24. Replace the logic board and the logic board screws. Base Reassembly iMac (Flat Panel) Take Apart - 103
Page 107
25. . Connect the following to the bottom housing: A Power supply connector B Hard drive/optical drive data cable C AC line filter connector D AirPort antenna connector E Plastic cable retainer and video cable F Grounding screw 104 iMac (Flat Panel) Take Apart Base Reassembly
Page 108
26. Apply thermal paste before closing the bottom housing. Squeeze a thin film of thermal paste onto the thermal pipe and mating surface. Spread the paste evenly. Base Reassembly iMac (Flat Panel) Take Apart - 105
Page 109
![Page 109
27. Replace the AirPort card (shown below).
28. Replace the memory (SO-DIMM, if present).
29. Close the bottom housing and replace the four torx screws.Replacement Note: These
torx screws must be tightened to at least 17 in.-lbs. If you do not have\
a
torque driver, you will have to make sure these screws are tightened by \
hand
FIRMLY, BUT NOT FORCIBLY. Or, purchase the service tool (076-0899) in \
order to ensure the thermal pipe is firmly mated with the top base. If t\
he
bottom housing is...](http://img.usermanuals.tech/thumb/462/38776/w300_imac-17-inch-1ghz-108.png "Page 109
27. Replace the AirPort card (shown below).
28. Replace the memory (SO-DIMM, if present).
29. Close the bottom housing and replace the four torx screws.Replacement Note: These
torx screws must be tightened to at least 17 in.-lbs. If you do not have\
a
torque driver, you will have to make sure these screws are tightened by \
hand
FIRMLY, BUT NOT FORCIBLY. Or, purchase the service tool (076-0899) in \
order to ensure the thermal pipe is firmly mated with the top base. If t\
he
bottom housing is...")
27. Replace the AirPort card (shown below). 28. Replace the memory (SO-DIMM, if present). 29. Close the bottom housing and replace the four torx screws.Replacement Note: These torx screws must be tightened to at least 17 in.-lbs. If you do not have\ a torque driver, you will have to make sure these screws are tightened by \ hand FIRMLY, BUT NOT FORCIBLY. Or, purchase the service tool (076-0899) in \ order to ensure the thermal pipe is firmly mated with the top base. If t\ he bottom housing is...
Page 110
30. Replace the user access door. Base Reassembly iMac (Flat Panel) Take Apart - 107