Home > Apple > Display > Apple imac 17 inch flat panel User Manual

Apple imac 17 inch flat panel User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple imac 17 inch flat panel User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 © 2002 Apple Computer, Inc. All rights reserved.  
     
     
    Service Source
    iMac (17-inch Flat Panel)
     
                                                                            \
                Updated  2003 June 3 
    						
    							 
    © 2002 Apple Computer, Inc. All rights reserved. 
     
     
     
    Service Source
    Take Apart
     
    iMac (17-inch Flat Panel) 
    						
    							 
     iMac (17-inch Flat Panel)  Take Apart -   
    1  
     Tools 
    Tools
     
    The following tools are recommended for the take apart procedures.
    • service repair kit (076-0900) includes: 
    – the service stand (076-0898)
    – diagnostic cables (076-0897) 
    • thermal paste (922-4757)
    • 
    torque driver (076-0899) 
    • 1.5 mm hex driver (for LCD bezel screws)
    • phillips #0 screwdriver)
    • torx screwdriver set (6, 8, 10, 15, 25)
    • plastic flatblade screwdriver or stylus
    •  needlenose pliers
    • ESD wriststrap and mat 
    Service Stand 
    						
    							 
    2 - 
     iMac (17-inch Flat Panel) Take Apart
     Tools 1. Support the computer by neck and the base (A). Gently position the computer in the 
    service stand with the flat panel facing up (B). 
    2.  
    Note:  
      The base of the computer can be rotated when servicing internal parts. 
    						
    							 
     iMac (17-inch Flat Panel)  Take Apart -   
    3  
     User Access Plate 
     User Access Plate
     
    Tools
     
    This procedure requires the following tools:
    • Phillips #0 screwdriver 
    Part Location
    Preliminary Steps
     
    Before you begin, do the following:
    • Position the computer in the service stand. 
    						
    							 
    4 - 
     iMac (17-inch Flat Panel) Take Apart
     User Access Plate 
    Procedure
     
    1. Loosen the four captive screws on the access panel.
    2. Remove the panel by grabbing onto two captive screws and lift the panel off the base. 
    						
    							 
     iMac (17-inch Flat Panel)  Take Apart -   
    5  
     AirPort Card 
    AirPort Card
     
    Tools
     
    This procedure requires no tools. 
    Part Location
    Preliminary Steps
     
    Before you begin, do the following:
    • Position the computer in the service stand.
    • Remove the user access plate. 
    						
    							 
    6 - 
     iMac (17-inch Flat Panel) Take Apart
     AirPort Card 
    Procedure
     
    1. Unplug all cables from the computer except the power cord. 
    2. 
    Important: 
     To avoid electrostatic discharge, always ground yourself by touching 
    metal before you touch any parts or install any components inside the computer. To 
    avoid static electricity building back up in your body, do not walk around the room until 
    you have completed the installation and closed the computer. 
    3. Touch a metal surface inside the computer to ground yourself.
    4. Unplug the power cord.
    5. Disconnect the AirPort antenna and pull the plastic tab to remove the card from the 
    slot. 
    						
    							 
     iMac (17-inch Flat Panel)  Take Apart -   
    7  
     Memory, SO-DIMM (user-installable) 
    Memory, SO-DIMM (user-
    installable)
     
    Tools
     
    No tools are required for this procedure. 
    Part Location
     
    Note: 
     The user-installable memory slot is identified as Slot J22 by Apple Hardware Test 
    and Apple System Profiler.  
    Preliminary Steps
     
    Before you begin, do the following:
    • Position the computer in the service stand.
    • Remove the user access plate. 
    Note: 
     There are two RAM expansion slots on the computer. One slot (top of the logic 
    board) accepts the factory-installed standard PC-133 168-pin DIMM. The other slot 
    (bottom of logic board) accepts a standard PC-133 144-pin SO-DIMM and is accessible 
    on the bottom of the computer. Only the SO-DIMM slot is accessible by the user.  
    						
    							 
    8 - 
     iMac (17-inch Flat Panel) Take Apart
     Memory, SO-DIMM (user-installable) 
    Procedure
     
    1. Unplug all cables from the computer except the power cord.
    2. 
    Important: 
     To avoid electrostatic discharge, always ground yourself by touching 
    metal before you touch any parts or install any components inside the computer. To 
    avoid static electricity building back up in your body, do not walk around the room until 
    you have completed the installation and closed the computer. 
    3. Touch a metal surface inside the computer to ground yourself.
    4. Unplug the power cord.
    5. Push the tabs outward to release the memory. 
    						
    All Apple manuals Comments (0)

    Related Manuals for Apple imac 17 inch flat panel User Manual