Apple ibook g4 User Manual

 
iBook G4 Take Apart -  
70  
 Top Shield2. Using a black stick, carefully peel up, but do not remove, any foil strips or pieces of 
tape.
  Note:
   
  When reassembling the computer, reuse the foil and tape to secure the 
replacement top shield.
3.
  Warning:
   
  Do not bend the top shield.
   
Lift the top shield off the computer, being careful where it might catch on the 
computer assembly.
4. Install the replacement top shield, and reassemble and test the computer.
  Replacement Note:
   With the...

 
71 -  
iBook G4 Take Apart
 Top Shield  Replacement Note:
   With the top shield removed, check the hard drive stiffener. 
Make sure it has a thin, foam strip backing. The stiffener can become loose. Make 
sure it is positioned over the hard drive and frame before replacing the top shield.
If the foam backing is missing, order a trackpad kit (Apple part number 076-1078), 
and replace the stiffener with one from the kit. 

 
iBook G4 Take Apart -  
72  
 Top Shield  Important:
   If you are installing the same top shield, remove the EMI finger by 
twisting it off of the shield. If you are replacing the top shield, make sure the shield 
does not have the EMI finger attached. A new foam pad on the trackpad overrides 
the need for the EMI finger. 

 
73 -  
iBook G4 Take Apart
 Top Shield  Replacement Note:
   Before installing the top shield, make sure cables are routed as 
shown, and fresh tape is installed where shown. 

 
iBook G4 Take Apart -  
74 
 I/O Bezel  I/O Bezel  Tools  • Soft cloth
• #0 Phillips screwdriver
• Black stick (or other nonconductive nylon or plastic tool)  Part Location
Preliminary Steps 
Before you begin, remove the following:
• Battery 
• Keyboard and RAM shield
• AirPort Extreme Card
• Memory card
• Bottom case
• Bottom shield
• DC-in board
• Top case
• Top shield 

 
75 -  
iBook G4 Take Apart
 I/O Bezel  Procedure  1. With the computer on a soft cloth, remove the two screws from the I/O bezel. 
2. Remove the I/O bezel from the computer frame.
  Note:
   When reassembling the computer, make sure that the I/O bezel is level and fits 
over all ports. 

 
iBook G4 Take Apart -  
76 
 I/O Bezel3. Install the replacement I/O bezel, and reassemble and test the computer.
  Note: When installing the replacement I/O bezel, make sure the bezel shield and the 
mylar panel fits over the underside of the logic board, as shown below.
Replacement Note: Note the placement of the long EMI strip that covers the FireWire 
port, USB ports, and display port. Make sure it is held in place by the single screw before 
reassembling the computer. 

77 - iBook G4 Take Apart
 RJ11 Modem Cable
RJ11 Modem Cable
Tools
• Soft cloth
• Black stick (or other nonconductive nylon or plastic tool)
Part Location
Preliminary Steps
Before you begin, remove the following:
• Battery 
• Keyboard and RAM shield
• AirPort Extreme Card
• Memory card
• Bottom case
• Bottom shield
• DC-in board
• Top case
• Top shield
• I/O bezel 

iBook G4 Take Apart - 78
 RJ11 Modem Cable
Procedure
1. With the computer on a soft cloth, lift up the modem sleeve and disconnect the RJ11 
modem cable from the modem board. 
2. Guide the cable up through the metal channel.
3. While supporting the computer assembly, slide the modem port forward and off of the 
logic board. 
4. Install the replacement RJ11 modem cable, and reassemble and test the computer. 

79 - iBook G4 Take Apart
 Hard Drive
Hard Drive
Tools
• Soft cloth
• #0 Phillips screwdriver
• Black stick (or other nonconductive nylon or plastic tool)
• Torx T8 screwdriver
Note: To organize the screws you remove from the computer, use a tray with divided 
compartments (such as a plastic ice cube tray).
Part Location
Preliminary Steps
Before you begin, remove the following:
• Battery 
• Keyboard and RAM shield
• AirPort Extreme Card