Apple ibook g4 14 inch late 2004 User Manual
Have a look at the manual Apple ibook g4 14 inch late 2004 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
iBook G4 (14-inch Late 2004) Take Apart - 140 Antenna Board Antenna Board Tools • Soft cloth • Black stick (or other nonconductive nylon or plastic tool) • #0 Phillips screwdriver Replacement Note: If the tape you remove from this assembly is worn and cannot be reused, use new Kapton tape (Apple part number 922-5025). Preliminary Steps Before you begin, remove the following: • Battery • Keyboard and RAM shield • AirPort Extreme Card • Memory card • Bottom case • Bottom shield • DC-in board • Top case • Top shield • Modem • Display module • LCD panel
141 - iBook G4 (14-inch Late 2004) Take Apart Antenna Board Procedure Note: Although your bezel assembly might appear somewhat different than shown, the steps to follow are the same. 1. With the bezel assembly lying on a soft cloth, peel up the tape from the antenna board. 2. Note the placement of the antenna board and the routing of the cables that are soldered to and run along the bottom of the antenna board.
iBook G4 (14-inch Late 2004) Take Apart - 142 Antenna Board3.Warning: When lifting the antenna board, be careful not to strain or pinch the cables. Replacement Note: The antenna board is held to the bezel assembly with double- sided tape on each end of the board. Use new double-sided tape when installing the replacement antenna board. Use a black stick to pry up the antenna board, but do not remove it yet. 4. Remove the 4.5-mm long Phillips screw from the bezel brace. 5. Lift up the bezel brace and release the cables from under the brace. 4.5 mm
143 - iBook G4 (14-inch Late 2004) Take Apart Antenna Board 6. With the antenna board loosened, note the cable routing on each side of the bezel. On the right, the antenna receptor cable is routed underneath the microphone cable through two channels before terminating at the receptor bracket. 7. Remove the two 3-mm long Phillips screws from the antenna receptor on the right side of the bezel assembly.
iBook G4 (14-inch Late 2004) Take Apart - 144 Antenna Board8. Tilt up the antenna receptor to remove it from the bezel assembly. 9. On the left side of the bezel, remove the two Phillips screws at the antenna receptor. 10. Tilt up the antenna receptor to remove it from the left side of the bezel assembly.
145 - iBook G4 (14-inch Late 2004) Take Apart Antenna Board 11. Unwrap the tape that secures the AirPort antenna cable to the cable bundle. 12. Use a black stick to lift out the cables from the channels. 13. Remove the antenna board with attached cables and antenna receptors.
iBook G4 (14-inch Late 2004) Take Apart - 146 Antenna Board14. Install the replacement antenna board, and reassemble and test the computer. Replacement Note: Make sure the right corner of the replacement antenna board aligns with the raised L-shaped guide in the bezel assembly, as shown. Replacement Note: Make sure the replacement antenna board does not cover or pinch any cables. Warning: Handle the replacement antenna board, receptors, and cables with care. Do not strain or pinch cables. Do not apply pressure to or bend the antenna receptors.
147 - iBook G4 (14-inch Late 2004) Take Apart Reed Switch Board Reed Switch Board Tools • Soft cloth • Black stick (or other nonconductive nylon or plastic tool) • #0 Phillips screwdriver Replacement Note: If the tape you remove from this assembly is worn and cannot be reused, use new Kapton tape (Apple part number 922-5025). Preliminary Steps Before you begin, remove the following: • Battery • Keyboard and RAM shield • AirPort Extreme Card • Memory card • Bottom case • Bottom shield • DC-in board • Top case • Top shield • Modem • Display module • LCD panel
iBook G4 (14-inch Late 2004) Take Apart - 148 Reed Switch Board Procedure Note: Although your bezel assembly might appear somewhat different than shown, the steps to follow are the same. 1. With the bezel assembly lying on a soft cloth, remove the one 3- mm long Phillips screw at the reed switch board. 2. Pull up the reed switch cables from the channels on the left side of the bezel.
149 - iBook G4 (14-inch Late 2004) Take Apart Reed Switch Board 3. Lift up the cables and peel up the tape that covers the cables running along the bottom of the inverter board.