AOR AR8200 Protocol Listing Manual

Page 11
MPSet memory channel as pass To set: MPn
n = 0 (pass off), n = 1 (pass on)
To read: MP (when in memory read mode)
Note: Setting pass on a memory channel excludes it from scans
Note: “?” is returned when not in M.RD mode
MQDelete bank or memory
channel MQ
Deletes the current memory channel (when in memory recall mode)
MQ
nn
Deletes memory channel 
nn
MQx%%
Deletes all memory channels from bank 
x.
Note: Responds with “?” when a memory channel is protected. Refer to PC, WM
and WP commands
MRRecall...

Page 12
NLNoise Limiter To set: NLn
n = 0 (off), n = 1 (on)
To read: NL
Response is NL
n
OFSelect offset frequency OFnnx
Selects offset frequency at index 
nn (00-47, 00=off) and defines offset to
be 
x (+/-)
OF
Returns with the current offset frequency data as follows:
OF
mmx RF0nnnnnnn00 (where mm is the offset index value and x is + or -)
Notes:
1.  OF can be used on its own or with MX and SE
2.  Allows access to a table of offset frequencies defined by OL
3.  Automode operation is switched off when...

Page 13
PPSet priority channel To set: PPxnn
Selects channel 
xnn as the priority channel,
where x is a bank A-J or a-j and nn is a channel number
To read: PP
Responds with PP
xnn
PQWait time for LC2 To set: PQnn
Sets time nn (00-99 corresponding to 000-990 mS in steps of 10 mS)
To read: PQ
Responds with PQnnn (000-999 mS)
Note:  This wait time is used as a buffer.
PRList pass frequencies PRxnn
Lists the pass frequency stored in pass channel nn of bank 
x (A-T, a-t or V)
PR
x
Lists all pass frequencies...

Page 14
RXRespond with current data RX
Recalls current operating parameters in the following formats
VFO mode
VF RF
nnnnnnnnnn STnnnnnn AUn MDn ATn
2-VFO mode
V
x RFnnnnnnnnnn STnnnnnn AUn MDn ATn
VFO search mode
VS V
x RFnnnnnnnnnn STnnnnnn AUn MDn ATn
VFO scan mode
VV V
x RFnnnnnnnnnn STnnnnnn AUn MDn ATn
Memory manual mode
MR MX
xnn MPn RFnnnnnnnnnn STnnnnnn AUn MDn ATn TMxxx...x
Scan mode
MS MX
xnn MPn RFnnnnnnnnnn STnnnnnn AUn MDn ATn TMxxx...x
Select scan mode
SM MX
xnn MPn RFnnnnnnnnnn STnnnnnn...

Page 15
SHSet offset step To set: SHnnnnm0
Set the tuning step size in Hz
To set: SH
nnn.nm
Set the tuning step size in kHz
SH+
nnnnm0, SH+nnn.nm or SH+ turns on step adjust
m is either 0 or 5
To read: SH
Responds with value, format: SH
nnnnm0x (x=+ step adjust on)
SIVoice Invertor on/off
Note: Requires VI8200
To Set: SIn
n=0 (off), n=1 (on)
To read: SI
Responds with SI
n SCnnn
Example:
SI1w SC051  when the invertor value is 051
Note: Refer to individual commands for details of each field.
SLLower search...

Page 16
TBSet Text Description for Bank To set: TBnxxxxxxxx
Sets the text for bank 
n (A-J or a-j) to be the 8-character ASCII comment
specified
TB or TB%%
Responds with a complete listing of the comments for each bank in the
following form:
TB
MW A:50 TBAAOR Test
MW a:50 TBa
MW B:50 TBBAOR
MW b:50 TBb
MW C:10 TBCAOR Test
MW c:90 TBc
MW D:50 TBDAOR Test
MW d:50 TBd
MW E:50 TBE
MW e:50 TBe
TB
x
Responds with the text for bank x in the following format:
TBA
TBAAOR Test
TISet priority interval To set: TI...

Page 17
VTVFO auto-store To set: VTn
Where 
n is defined as follows:
0 Off
1 On, Auto-store to bank J
2 On, erase bank J
To read: VT
Responds with VT
n as above
Note: VT2 response is equivalent to VT1
VVVFO Scan To set: VVn
Where 
n=0 (2-VFO mode) or n=1 (VFO scan mode)
WMWrite Protect Bank To set:
WM
xn
Where 
x is bank (A-J or a-j) and n=0 (protect off), n=1 (protect on)
To read:
WM or WM%%
Responds with a listing of 10 banks starting from the last queried bank.
Example:
WM
WM F0
WM f0
WM G0
WM g0
WM...

Page 18
Up/DownIncrementn
where 
n is a binary byte value as follows
ð0x1c
ï0x1d
ñ0x1e
ò0x1f
(8)  AOR PC Windows control software & bandplan editing
A dedicated 
PC Windows package is supplied on CD-ROM with the CC8200 lead, it is also available as a FREE download from the
AOR web site  WWW.AORJA.COM
It is recommended that the AOR software be used should you wish to edit the automode bandplan data.  The protocol information
for bandplan has not been included in the CC8200 command listing as errors...

Page 19
Installing the software
To install the AOR software run the INSTALL.EXE program from the CD-ROM (
x:\English\CC8200\cont-soft\install.exe
where ‘
x’ is your CD-ROM drive letter).  If installing from a web download, expand the ZIP file into a temporary directory on your
hard drive then run the INSTALL.EXE
A directory will be created on your hard drive along with a program group from the START/PROGRAMS button of the desktop.
This software package will also provide additional facilities such as...

Page 20
CC8200 - AR8200 REMOTE CONTROL
Thank you for purchasing the CC8200.
This CD-ROM is supplied with the CC8200 and contains the following data in both Japanese and English languages.
Should you wish to use English language, please select the files under , should you wish to use Japanese
language, please select the files under .
CD-ROMreadme-j.txt  Read me file in Japanese language
readme-e.txt  Read me file in English language (this information sheet)

  Adobe
® Acrobat® Reader

  AR8200 bandplan...