AOC N941sw User Manual

 41 10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory:   
X:\Driver\module name    (where X is the drive letter designator for the CD-ROM drive). 
 
 
 
11. Select the xxx.inf file and click the “Open” button. Click the “OK” button.  
 
12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk 
drive.  
 
13. Close all open windows and remove the CD.   
 
14. Restart the system. The system will...

 42
Windows Vista 
 
1. Click Start  and Control Panel. Then, double-click on Appearance and Personalization. 
    
  
2. Click Personalization and then Display Settings. 
   
 
3. Click Advanced Settings.... 
    
 
 

 43 4. Click Properties in the Monitor tab. If the Properties button is deactivated, it means the configuration for your 
monitor is completed. The monitor can be used as is. 
If the message Windows needs... is displayed, as shown in the figure below, click Continue. 
   
 
5. Click Update Driver... in the Driver tab.   
   
 
6. Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers 
on my computer. 
 
 
7. Click on the Have disk... button, then...

 44
Windows XP 
 
1. Start Windows® XP   
2. Click on the Start button and then click on Control Panel.   
 
 
3. Select and click on the category ‘Appearance and Themes’ 
 
 
4. Click on the Display Item.   
 
    
 

 45 5. Select the Settings tab then click on the Advanced button.   
 
 
6. Select Monitor tab 
- If the Properties button is inactive, it means your monitor is properly configured. Please stop installation. 
- If the Properties button is active, click on Properties button. 
Please follow the steps below.   
 
 
7. Click on the Driver tab and then click on Update Driver... button.   
 
   
 

 46 8. Select the Install from a list or specific location [advanced] radio button and then click on the Next button.   
 
 
9. Select the Dont Search. I will choose the driver to install radio button. Then click on the Next button.   
 
 
10. Click on the Have disk... button, then click on the Browse... button and then select the appropriate drive F: 
(CD-ROM Drive).   
 
11. Click on the Open button, then click the OK button.   
12. Select your monitor model and click on the Next button. 
- If you can...

 47
Windows 2000 
 
1. Start Windows® 2000   
2. Click on the Start button, point to Settings, and then click on Control Panel.   
3. Double click on the Display Icon.   
4. Select the Settings tab then click on Advanced....   
5. Select Monitor   
- If the Properties button is inactive, it means your monitor is properly configured. Please stop installation.   
- If the Properties button is active. Click on Properties button. Please follow the steps given below.   
6. Click on Driver and then click on...

 48
i-Menu 
 
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on 
screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation 
guide.  
 

 49
Troubleshoot 
 
Problem & Question  
Possible Solutions 
 
 
Power LED Is Not ON  
Make sure the power button is ON and the Power Cord is properly connected 
to a grounded power outlet and to the monitor.   
 
 
 
 
 
 
 
 
 
 
No images on the screen  
Is the power cord connected properly? 
Check the power cord connection and power supply. 
Is the cable connected correctly? 
(Connected using the D-sub cable) 
Check the DB-15 cable connection.    
(Connected using the DVI cable) 
Check the DVI cable...

 50  
 
 
 
Monitor Is Stuck In Active 
Off-Mode  
The Computer Power Switch should be in the ON position.   
The Computer Video Card should be snugly fitted in its slot.   
Make sure the monitors video cable is properly connected to the computer. 
Inspect the monitors video cable and make sure no pin is bent.   
Make sure your computer is operational by hitting the CAPS LOCK key on 
the keyboard while observing the CAPS LOCK LED. The LED should either 
turn ON or OFF after hitting the CAPS LOCK key....