AOC L26W898 User guide

 20
BASIC OPERATION 
To operate your LCD TV, you may use the TV remote control or top panel buttons to select input 
source, change channels, or adjust volume. 
 
Turning on the LCD TV 
Before using the LCD TV: 
1.  Connect external equipment properly. 
2.  Insert the power plug and the power LED indicator will light red. 
 
Power On/Off 
T
o turn the LCD TV on/off:   
Press  POWER  button under the LCD TV, or press the  POWER button on your remote control to 
turn on/off the TV. The power LED indicator...

 21
 
 
 
 
 
Select input source 
To select the required input source: 
Press the  INPUT button on the remote control, Use  ▲▼ to select the 
required input source between  T V, A V, S- Video,  YPbPr 1,  YPbPr 2, 
VGA, HDMI 1, and HDMI  2. 
To confirm the selection, press  ENTER.
 
  4. 
Select your tuner mode from  Air or Cable, 
then press  ► to continue. Connect cable 
and/or antenna, and select Scan or Skip 
Scan with  ▲ or  ▼, then press  ► to 
continue. If you select Skip Scan at this 
step, you...

 22
Volume Adjusting 
Press VOL +/- to adjust volume.   
To turn off the volume, press MUTE. 
To restore volume, press MUTE again, or press VOL +/- directly. 
 
 
Sound Mode Select 
Repeatedly press SOUND key to select the sound mode between Off, Concert, Living Room, Hall, 
Bathroom, Cave, Arena, or Church. 
 
Picture Mode Select 
Repeatedly press PICTURE key to select picture mode between User, Cinema, Sport, Vivid, and 
Hi-Bright. 
 
INFO 
To display the current information of the LCD TV:   
Press...

 23
2. In DTV mode Use “ -” button to select the sub channel in DTV. 
Ex: Your desired number is 80-3.   
Press  8 →  press  0 →  press ” -”  →  press  3. 
• Whether in ATV or DTV, after you input the channel numbers, press  ENTER button to direct 
to the channel immediately, or wait for 3 seconds to change automatically. 
• Return to the previous channel, press  RETURN button. 
※  How to switch between Air TV and Cable TV? 
When in TV mode, press TV/CATV button to switch , or go to the Tuner Mode in...

 24
ADVANCED OPERATION—OSD MENU 
 
Video Menu 
—To adjust the picture quality 
In TV, A V, S- Video,  YPbPr 1,  YPbPr 2, HDMI 1, HDMI 2 source: 
(When in AV, S-Video, YPbPr or HDMI source, the TV option on the left does not appear.)  
 
 
In VGA source: 
 
z  Picture Mode:  To select picture mode between User, Cinema, Sport, Vivid, and Hi-Bright. 
z   Noise Reduction:  T o reduce the noise level of connected equipment. Select from Lo w, 
Medium,  Strong, or O ff. 
z  Brightness:  To adjust luminance of...

 25
 
z Auto Adjust: Press ENTER to auto adjust picture’s horizontal position, vertical position, fine 
tune and H-Size. 
z VGA: Press ENTER to adjust VGA setting.   
 

 26
In AV, S- Video,  YPbPr 1,  YPbPr  2, HDMI 1, HDMI 2, VGA  source: 
 
z  Balance:  To adjust left and right audio balance. 
z  Bass:  To adjust bass. 
z  Treble:  To adjust the treble. 
z   Surround:  To enjoy a concert hall e ffect, select “ On” when stereo is playing. 
z  Reverb:  To enjoy the reverb sound effect of Concert, Living Room, Hall, Bathroom, Cave, 
Arena, or Church. 
z   Equalizer:  T o select equalizer modes from Rock,  Pop , Live, Dance,  T echno, Classic, So ft.   
z  SPDIF Type:  To...

 27
z Channel Skip:  Press ENTER  to skip the channel. To restore the channel, press  ENTER again. 
 
z  MTS:  To select audio available mode.  
z  Audio Language:  To select available audio language.  
 
 
Setup Menu 
—To set up OSD window 
In TV, AV, S-Video,  YPbPr 1, YPbPr 2, HDMI 1, HDMI 2  source: 
(When in AV, S-Video, YPbPr or HDMI source, the TV option on the left does not appear.) 
 
 
In VGA source: 
 
z OSD Language: To select an OSD language from English, Spanish or French. 
z 
Aspect Ratio:...

 28
z  Time Setup:  T o  set  Time  Zone,  Time,  Sleep  Time r,  Auto  Sleep, and Daylight Saving.  
 

 29