AOC E2343fk User Manual

							
 11
Adjusting Viewing Angle 
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitors angle to your 
own preference.   
Hold the stand so you will not topple the moni tor when you change the monitors angle.   
You are able to adjust the monitors angle from -3° to 12 °.   
 
 
NOTE: 
Do not touch the LCD screen when you change the a ngle. It may cause damage or break the LCD screen.
-312
  
						

							
 12
Connecting the Monitor 
Cable Connections On Back of Monitor and Computer: 

 
1. 
 Power   
2. D-SUB
     
3.   DVI
 
   
To protect equipment, always turn off the PC and LCD monitor before connecting.   
 
1      Connect the power cable to the AC  port on the back of the monitor.   
2      Connect one end of the 15-pin D-Sub cable to t he back of the monitor and connect the other end to the 
computers D-Sub port.   
3       
4    Turn on your monitor and computer.   
 
If your monitor displays an image, installation is comp lete. If it does not display an image, please refer 
Troubleshooting.   
 
（Optional-Requires a video card with DVI port ）-Connect one end of the DVI cable to the
back of the monitor and connect the other end to the computer’s DVI port. 
 
						

							
 13
Wall Mounting 
Preparing to Install An Optional Wall Mounting Arm.   
This monitor  can  be  attached  to  a  wall  mounting  arm  you  purchase  separately.  
Disconnect  power  before  this  procedure.  Follow  these  steps:  
1   Place  monitor  on  the  firm  surface  (such  as,  table)   
2   Use  your  hands  to hold  the  monitor  base   
3   Use  your  hands  to fold  the  monitor  base  as  figure  instructed  above  by  switch  
safety  lock  to  the  right  side 
4   Once  the monitor  base  begin  to  fold  you  can release  the  safety  lock  (caution:  you 
must  hear  “click”  after  you fold  the  monitor  base  to  wall  mount  position  to  
ensure  safety lock  is  lock  properly.)   
5   Follow  the  manufacturers  instructions  to  assemble  the  wall  mounting  arm.   
6   Place  the  wall  mounting  arm  onto  the  back  of  the  monitor.  Line  up  the  holes  of  
the  arm  with  the holes  in  the  back  of  the  monitor.   
7   Insert  the  4  screws  into  the  holes  and  tighten.   
8   Reconnect  the  cables.   Refer  to the  users  manual  that  came  with  the optional  
wall  mounting  arm  for  instructions  on  attaching  it  to  the  wall.   
Noted  :    VESA  mounting  screw  holes  are  not available  for  all models,  please check  
with  the dealer  or  official  department  of  AOC.   
 
 
						

							
 14
Adjusting 
Setting Optimal Resolution 
Windows Vista   
For Windows Vista: 
1 Click START.  
2 Click  CONTROL PANEL. 
 
 
3 Click  Appearance and Personalization.  
 
 
4 Click  Personalization   
 
 
 
						

							
 15
5 Click 
Display Settings.   
 
 
6 Set the resolution  SLIDE-BAR to 1920 by 1080.   
 
 
						

							
 16
Windows XP   
For Windows XP: 
1 Click START.   
 
 
2 Click  SETTINGS. 
 
3 Click  CONTROL PANEL.   
 
4 Click  Appearance and Themes.  
 
 
5 Double click  DISPLAY.  
 
 
 
						

							
 17
6 Click SETTINGS. 
 
7 Set the resolution SLIDE-BAR to 1920 by 1080.   
 
Windows ME/2000 
For Windows ME/2000: 
1 Click START.  
2 Click SETTINGS.  
3 Click CONTROL PANEL.  
4 Double click DISPLAY.  
5 Click SETTINGS.  
6 Set the resolution SLIDE-BAR to 1920 by 1080.
  
 
 
 
						

							
 18
Hotkeys 
 
 

 
Power  
Press the Power button to turn 0n/off the monitor. 
 
Eco Mode / < 
Press the Eco key continuously to select the Eco m ode of brightness when there is no OSD ( Eco mode hot key 
may not be available in all models).   
 
4:3 or wide image ratio / > 
When there is no OSD, press   hotkey continuously to c hange 4:3 or wide image ratio. (If the product screen size 
is 4:3 or input signal resolution is wide format, the hot key is disable to adjust. )   
   Eco Mode/<     4:3 or wide /
>    Menu/Enter
   Po wer
>
 
Auto/Source/Exit 
When the OSD is closed, press Auto/Source/Exit button continuously about 2 second to 
do auto configure (only for the m
odels with dual or more inputs). 
When the OSD is closed, press Auto/Sour ce/Exit button will be Source hot key 
function(Only for the models with dual or  more inputs).Press Auto/Source/Exit button 
continuously to select the input source  showed in the message bar, press Menu/Enter 
button to change to the source selected. 
Auto/Source/Exit 
 
						

							
 19
OSD Setting 
 
Basic and simple instruction on the control keys. 
 
 
 
 
1) Press the  MENU-button  to activate the OSD window.   
2) Press  < or > to navigate through the functions. Once t he desired function is highlighted, press the  MENU-button 
to activate sub-menu . Once the des ired function is highlighted, press MENU-button to activate it.   
3) Press  < or > to change the settings of the selected function. Press  < or > to select another function in sub-menu . 
Press  AUTO to exit . If you want to adjust an y other function, repeat steps 2-3.   
4) OSD Lock Function: To lock the OSD, press and hold the  MENU button while the monitor is off and then press 
power button  to turn the monitor on. To un-lock the OSD - press and hold the  MENU button while the monitor is 
off and then press  power button to turn the monitor on. 
 
Notes:  
1) If the product has only one signal input, the it em of Input Select is disable to adjust. 
2) If the product screen size is 4:3 or input signal resolution  is wide format, the item of Image Ratio is disable to 
adjust.    
3) One of DCR, Color Boost, and Picture Boost functions is  active, the other two function is turned off accordingly. 
 
 
 
 
 
						

							
 20
Luminance 
 
Press (Menu) to display menu. 
Press  or  to select  
(Luminance)
, and press to enter. 
Press  or   to select submenu, press 
to enter, and press  or  to 
adjust. 
Press  to exit.