AOC 916vwa User Manual

							    916Vwa User Manual 
1. Preface About This Guide 
 
This guide describes the monitors features, setup,  and operation. lnformation in this document is subject to change w ithout notice. 
The sections are as follows: 
·  
Safety Instructions
: lists safety information.  
· 
Setup
: describes the initial setup process.  
· 
Using the Monitor
: gives an overview of how to use the monitor.  
· 
Drivers
: provides driver installation instructions for Win dows.  
· 
Technical Support 
: provides tips and solutions for common problems.   
· 
Product Information
: lists the technical specifications of the monitor .  
· 
Warranty Statement
: Warranty Statement used in Europe.  
National Conventions 
 
The following subsections describe notational conve ntions used in this document.  
Notes, Cautions, and Warnings  
Throughout this guide, blocks of text may be accomp anied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and war nings, and they are used as 
follows: 
 NOTE: A NOTE indicates important information that h elps you make better use of your computer system.
 
 CAUTION: A CAUTION indicates either potential damag e to hardware or loss of data and tells you how to avoid the problem.
 
 WARNING: A WARNING indicates the potential for bodi ly harm and tells you how to avoid the problem. 
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.  Product Registration 
 
Please link
 www.aoc.com
, select your country or region, log in Product Reg istration to register . 
    
  
						

							2. Safety Introduction FCC Notice 
 
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) 
NOTE:  This equipment has been tested and found to comply  with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d esigned to provide 
reasonable protection against harmful interference  in a residential installation. This equipment generates, uses and can radiate radio frequency energy,  and if not installed and used in 
accordance with the instructions, may cause harmful  interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to r adio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following me asures: 
1.  Reorient or relocate the receiving antenna.   
2.  Increase the separation between the equipment an d receiver.  
3.  Connect the equipment into an outlet on a circui t different from that to which the receiver is connected.  
4.  Consult the dealer or an experienced radio/TV te chnician for help.  
NOTICE :  
1.  The changes or modifications not expressly appro ved by the party responsible for compliance could void the users authority to operate the equipment.  
2.  Shielded interface cables and AC power cord, if  any, must be used in order to comply with the emission limits.  
3.  The manufacturer is not responsible for any radi o or TV interference caused by unauthorized modification to this equipment. It is theresponsibilities of the user to correct 
such interference.  WEEE Declaration 
 
Disposal of Waste Equipment by Users in Private Hou sehold in the European Union.  
 
This symbol on the product or on its packaging indi cates that this product must not be disposed of with your other household waste.Instead, it is your responsibility to dispose of your 
waste equipment by handing it over to a designated  collection point for the recycling of waste electrical and electronic equipment.The separate collectio n and recycling of your waste 
equipment at the time of disposal will help to cons erve natural resources and ensure that it is recycled in a manner that protects human health and the e nvironment. For more 
information about where you can drop off your waste  equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you 
purchased the product . 
HG Declaration 
 
SAFETY: Lamp Disposal  
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUS T BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE 
INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLI ANCE AT 
WWW.EIAE.ORG
. 
  
						

							Precautions
 
 WARNING: Use of controls, adjustments, or procedure
s other than those specified in this documentation may result in exposure to shock, electrical hazards , and/or 
mechanical hazards.  
Read and follow these precautions when connecting a nd using your computer monitor:  
PRECAUTIONS  · 
Do not use the monitor near water, e.g. near a bath tub, washbowl, kitchen sink, laundry tub, swimming  pool or in a wet basement.  
· 
Do not place the monitor on an unstable cart, stand , or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Us e only a cart or stand 
recommended by the manufacturer or sold with the mo nitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer an d follow the kit 
instructions.  
·  
Slots and openings in the back and bottom of the ca binet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from  overheating, be sure 
these openings are not blocked or covered. Do not p lace the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radi ator or heat register. 
Do not place the monitor in a bookcase or cabinet u nless proper ventilation is provided.  
· 
The monitor should be operated only from the type o f power source indicated on the label. If you are not sure of the type of power supplied to your home,  consult your dealer 
or local power company.  
·  
The monitor is equipped with a three-pronged ground ed plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your 
outlet does not accommodate the three-wire plug, ha ve an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not  defeat the safety 
purpose of the grounded plug.  
·  
Unplug the unit during a lightning storm or when it  will not be used for long periods of time. This will protect the monitor from damage due to power sur ges.  
· 
Do not overload power strips and extension cords. O verloading can result in fire or electric shock.  
· 
Never push any object into the slot on the monitor  cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the mon itor.  
· 
Do not attempt to service the monitor yourself; ope ning or removing covers can expose you to dangerous  voltages and other hazards. Please refer all servicing to qualified 
service personnel.  
·  
To ensure satisfactory operation, use the monitor o nly with UL listed computers which have appropriate  configured receptacles marked between 100 - 240V A C, Min. 5A.  
· 
The wall socket shall be installed near the equipme nt and shall be easily accessible.  
· 
For use only with the attached power adapter (Outpu t 12Vdc) which have UL,CSA listed license(Only for monitors with power adapter ).  
3. Setup Setup the stand and base
 
Please setup or remove the base following below ste ps.  
 
						

							 
Adjusting Viewing Angle
 
· 
For optimal viewing it is recommended to look at th e full face of the monitor, then adjust the monitors angle to your own preference.  
· 
Hold the stand so you do not topple the monitor whe n you change the monitors angle.  
· 
You are able to adjust the monitors angle from -5° to 20°.  
  
						

							 
NOTE: 
Do not touch the LCD screen when you change the ang le. It may cause damage or break the LCD screen.  
    
   
Attaching the Cables
 
Cable Connections On Back of Monitor and Computer  
  
						

							 
1.Power  
2.audio 
3. DVI 
4. Analog 
Turn off your computer before performing the proced ure below. 
1.  Connect the power cable to the AC port on the ba ck of the monitor.  
2.  Connect one end of the 15-pin D-Sub cable to the  back of the monitor and connect the other end to the computers D-Sub port.  
3.  Turn on your monitor and computer.  
If your monitor displays an image, installation is  complete. If it does not display an image, see
 Troubleshooting
. 
  
						

							   Attaching Wall Mounting Arm
 
Preparing to Install An Optional Wall Mounting Arm   
 
  
						

							This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before t his procedure. Follow these steps: 
1.  Remove the base.   
2.  Follow the manufacturers instructions to assemb le the wall mounting arm.  
3.  Place the wall mounting arm onto the back of the  monitor. Line up the holes of the arm with the holes in the back of the monitor.  
4.  Insert the 4 screws into the holes and tighten.   
5.  Reconnect the cables.  Refer to the users manua l that came with the optional wall mounting arm for instructions on attaching it to the wall   
4. Using the Monitor Setting the Optimal Resolution 
 
The recommended resolution for this monitor is 1440  by 900. To setup the monitor to this resolution, follow the steps below. 
1.  Click  START.  
2.  Click  SETTINGS .  
3.  Click  CONTROL PANEL .  
4.  Double click  DISPLAY.  
5.  Click  SETTINGS .  
6.  Set the resolution  SLIDE-BAR to 1440 by 900.  
External Controls
 
Press the power button to turn the monitor on or of f. The other control knobs are located at front panel of the monitor (See Figure ). By changing these  settings, the picture can be 
adjusted to your personal preferences.  
* The power cord should be connected. 
* Press the power button to turn on the monitor. Th e power indicator will light up.  
 
						

							 
1. Auto Config  
2. Volume / - 
3. Volume / +  
4. Menu / Enter  
5. Power Button & Indicator 
OSD Settings
 
·  
Press the MENU-button to activate the OSD window.  
· 
Press+ or - to navigate through the functions. Once  the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has a sub-menu, press or 
again to navigate through the sub-menu functions.On ce the desired function is highlighted, press MENU-button to activate it.  
· 
Press+ or - to change the settings of the selected  function. To exit and save, select the exit function. If you want to adjust any other function, repeat  steps 2-3.  
· 
OSD Lock Function: To lock the OSD, press and hold  the MENUbutton while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - 
press and hold the MENUbutton while the monitor is  off and then press power button to turn the monitor on.  
· 
Press Exit key continually for 7 sec. to turn on or  off DDC-CI.  
  
						

							 
DCB Adjustment 
 
What is DCB?  
  
Dynamic Color Boost (DCB) is an advanced color adju stment technology. Through analyzing RGB signals, DCB creates more vivid and natural images to suit various color 
environment needs. DCB has two types of color enhan cers: “Color Boost” and “Picture Boost” .  
 
       DDC: Dynamic color control  
       ICM: Intelligent color management    
1) How to use Color Boost?   
 
YCM adjustment:  In addition to the basic R (red), G (green), B (bl ue) color adjustments, Color Boost has added Y (yel low), B (blue), and M (magenta) for more color fine-tuning 
options. YCM adjustments are in the third icon labe led Color Temperature in the OSD menu. When adjus ting YCM values, RBG values will also be changed automatically due to the 
color correlation between RGB and YCM.