AOC 2330v User Manual

							5 Click Display Settings.  
 
 
6 Set the resolution SLIDE-BAR to 1920 by 1080.  
  
 
For Windows XP: 
1 Click START.  
2 Click SETTINGS. 
3 Click CONTROL PANEL.  
 
						

							 
 
4 Click Appearance and Themes. 
 
 
5 Double click DISPLAY.  
 
 
6 Click SETTINGS. 
 
						

							7 Set the resolution SLIDE-BAR to 1920 by 1080.  
 
For Windows ME/2000: 
1 Click START.  
2 Click SETTINGS.  
3 Click CONTROL PANEL.  
4 Double click DISPLAY.  
5 Click SETTINGS.  
6 Set the resolution SLIDE-BAR to 1920 by 1080.     
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
						

							 
Power / Menu  
         Press to turn on monitor. When monitor is on, press to activate main menu. Press and hold 2 seconds to turn 
off.  
Eco (DCR) / Up   
            Press UP key to select different brightness eco-modes:   Standard, Text, Internet, Game, Movie, Sports and 
DCR (Dynamic Contrast Ratio).  When the main menu or sub-menu is active, the UP key functions as to navigate 
up.    
Source(Auto) / Down 
  
 Source hot key : When the OSD is closed, press Auto/Source button will be Source hot key function (Only for the 
models with dual or more inputs) .Press Source button continuously to select the input source showed in the 
message bar , press Menu/Enter button to change to the source selected.  
Auto configure hot key: When the OSD is closed, press Auto/Source button continuously about 2 second to do auto 
configure.  
Contrast / Left  
           Press LEFT key to activate Contrast menu and reduce Contrast, and press RIGHT key to increase Contrast. 
When the main menu or sub-menu is active, the LEFT key functions as to select down or reduce value.   
 
4:3 or Wide / Right 
          Press RIGHT key to change the screen aspect ratio between standard 4:3 format or Wide format.   When the 
input resolution is wide format, the aspect ratio hotkey is disabled. When the main menu or sub-menu is active, the 
RIGHT key functions as to select up or increase value.  
  
 
 
						

							 
  Luminance Contrast  Brightness  Eco mode  Gamma  DCR    
 
  Image Setup  Clock  Phase H.Position  V.Position      
 
  Color Temp.  Color Temp.  User-R User-G User-B    
 
  Color Boost  Full Enhance  Nature Skin Green Field Sky-blue  AutoDetect  Demo  
 
  Picture Boost  Frame Size  Brightness  Contrast  H. position  V.position Bright Frame  
 
  OSD Setup  H.Position V.Position  Timeout  Transparence Language    
 
  Extra Input Select Auto Config  Image Ratio DDC-CI Information    
 
  Reset Reset           
 
  Exit Exit            
  
Luminance ---Contrast, Brightness, Eco mode, Gamma, DCR 
Contrast 
Brightness 
Eco mode 
Gamma 
DCR 
  
Notes : When Eco mode is not set as “Standard”, Contrast and Brightness can not be adjusted; When DCR is set as 
“On”, Contrast, Brightness, Eco mode and Gamma can not be adjusted. 
 
 
 
 
 
 
						

							Problem & Question Possible Solutions 
Power LED Is Not ON 
 Make sure the power button is ON and the Power Cord is properly connected 
to a grounded power outlet and to the monitor.  
No images on the 
screen 
 Is the power cord connected properly? 
  Check the power cord connection and power supply. 
 Is the cable connected correctly? 
  
(Connected using the D-sub cable) 
Check the DB-15 cable connection.   
(Connected using the DVI cable) 
Check the DVI cable connection.  
* DVI input is not available on every model. 
 If the power is on, reboot the computer to see the initial screen (the login 
screen), which can be seen. 
  
If the initial screen (the login screen) appears, boot the computer in the 
applicable mode (the safe mode for Windows ME/XP/2000) and then change the 
frequency of the video card. 
(Refer to the Setting the Optimal Resolution) 
If the initial screen (the login screen) does not appear, contact the Service 
Center or your dealer.  
 Can you see Input Not Supported on the screen? 
  
You can see this message when the signal from the video card exceeds the 
maximum resolution and frequency that the monitor can handle properly. 
Adjust the maximum resolution and frequency that the monitor can handle 
properly.  
 Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are 
available at : here)  
Picture Is Fuzzy & 
Has Ghosting 
Shadowing Problem  
 Adjust the Contrast and Brightness Controls.  
 Press to auto adjust.  
 Make sure you are not using an extension cable or switch box. We recommend 
plugging the monitor directly to the video card output connector on the back .  
Picture Bounces, 
Flickers Or Wave 
Pattern Appears In 
The Picture 
 Move electrical devices that may cause electrical interference as far away from 
the monitor as possible.  
 Use the maximum refresh rate your monitor is capable of at the resolution your 
are using.  
Monitor Is Stuck In 
Active Off-Mode 
 The Computer Power Switch should be in the ON position.  
 The Computer Video Card should be snugly fitted in its slot.  
 Make sure the monitors video cable is properly connected to the computer.  
 Inspect the monitors video cable and make sure no pin is bent.  
 Make sure your computer is operational by hitting the CAPS LOCK key on the 
keyboard while observing the CAPS LOCK LED. The LED should either turn 
ON or OFF after hitting the CAPS LOCK key.  
Missing one of the 
primary colors (RED, 
GREEN, or BLUE) 
 Inspect the monitors video cable and make sure that no pin is damaged.  
 Make sure the monitors video cable is properly connected to the computer.  
Screen image is not 
centered or sized 
properly 
 Adjust H-Position and V-Position or press hot-key (AUTO).  
Picture has color 
defects (white does 
not look white) 
 Adjust RGB color or select desired color temperature.  
 
						

							 
LCD Panel  
Model number  2330V 
Driving system  TFT Color LCD  
Viewable Image 
Size 584mm diagonal 
Pixel pitch  0.2655mm(H) x 0.2655mm(V) 
Video  R, G, B Analog lnterface & Digital Interface 
Separate Sync.  H/V TTL 
Display Color  16.7M Colors  
Dot Clock  148.5 MHz  
Resolution  
Horizontal scan 
range  30 kHz - 83 kHz 
Horizontal scan 
Size(Maximum)  509.76mm  
Vertical scan range  56 Hz - 75 Hz  
Vertical scan 
Size(Maximum)  286.74mm  
Optimal preset 
resolution  1920 x 1080 (60 Hz) 
Highest preset 
resolution  1920 x 1080 (60 Hz)  
Plug & Play  VESA DDC2B/CI  
Input Connector  D-Sub 15pin & DVI-D  
Input Video Signal  Analog: 0.7Vp-p(standard), 75 OHM, Positive & DVI-D Digital Interface (TMDS)  
Power Source  100~240VAC, 50/60Hz  
Power 
Consumption  
Typical < 58 W  
Standby < 1 W  
Physical 
Characteristics  
Connector Type  15-pin Mini D-Sub & DVI-D  
Signal Cable Type  Detachable  
Dimensions & 
Weight:  
Height (with base)  418.85 mm 
Width  563mm 
Depth  219.58mm 
Weight (monitor only)  5.5 kg 
Weight (with packaging)  7.0 kg 
Environmental  
Temperature:  Operating  0° to 40°  
Non-Operating  -20°to 60° 
Humidity:  Operating  10% to 85% (non-condensing)  
Non-Operating  5% to 80% (non-condensing)  
Altitude:  Operating  0~ 2000m (0~ 10000 ft )  
Non-Operating  0~ 2000m (0~ 15000 ft )      
  
 
 
 
 
 
						

							FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) 
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures: 
1. Reorient or relocate the receiving antenna.  
2. Increase the separation between the equipment and receiver.  
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
4. Consult the dealer or an experienced radio/TV technician for help.  
NOTICE : 
1. The changes or modifications not expressly approved by the party responsible for compliance could void the 
users authority to operate the equipment.  
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission 
limits.  
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to 
this equipment. It is theresponsibilities of the user to correct such interference. It is the responsibility of the 
user to correct such interference. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
						

							WARRANTY STATEMENT 
for AOC Color Monitors 
Including those Sold within North America as Specified 
Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a 
period of three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original 
date of consumer purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. 
) will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or 
rebuilt product at no charge except as *stated below. The parts or product that are replaced become the 
property of EPI. 
 
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service 
Center closest to your area. Deliver the product freight pre-paid, along with the dated proof of purchase, 
to the EPI Authorized Service Center. If you cannot deliver the product in person: 
 Pack it in its original shipping container (or equivalent)  
 Put the RMA number on the address label  
 Put the RMA number on the shipping carton  
 Insure it (or assume the risk of loss/damage during shipment)  
 Pay all shipping charges  
 
EPI is not responsible for damage to inbound product that was not properly packaged. 
EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is 
not responsible for any costs associated with the transportation of product across international borders. This includes 
the international borders of the countries within this warranty statements. 
 
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free 
number (888) 662-9888. Or you can request an RMA Number online at www.aoc.com/na-warranty. 
 
* This limited warranty does not cover any losses or damages that occur as a result of:  
 Shipping or improper installation or maintenance  
 Misuse  
 Neglect  
 Any cause other than ordinary commercial or industrial application  
 Adjustment by non-authorized source  
 Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service 
Center  
 Improper environment  
 Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities  
This three-year limited warranty does not cover any of the products firmware or hardware that you or any third party 
have modified or altered; you bear the sole responsibility and liability for any such modification or alteration. 
 
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD 
OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL FROM 
THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) 
APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW 
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT 
APPLY TO YOU. 
 
 
						

							EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE. 
EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER 
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT W HOSE DEFECT OR DAMAGE IS THE 
BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF 
PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR 
CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE 
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION 
MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. 
YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE. 
 
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United 
States, Alaska, and Hawaii. 
Outside the United States of America, this limited warranty is only valid for Products purchased in Canada. 
 
For service in South America, refer to the SA Service Center List for a list of authorized service providers in South 
America.