AOC 2216va User Manual

       
2216Va User Manual 
1. Preface About This Guide  
This guide describes the monitors features, setup,  and operation. lnformation in this document is subject to change w ithout notice. 
The sections are as follows: 
·  
Safety Instructions
: lists safety information. 
· 
Setup
: describes the initial setup process. 
· 
Using the Monitor
: gives an overview of how to use the monitor. 
· 
Drivers
: provides driver installation instructions for Win dows. 
· 
Technical Support 
: provides tips and...

 WARNING: 
A WARNING indicates the potential for bodily harm and tells you how to avoid the problem
.  
Some warnings may appear in alternate formats and m ay be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated 
by regulatory authority.   Product Registration   
Please link
 www.aoc.com
, select your country or region, log in Product Reg istration to register.
 
2. Safety Introduction 
FCC Notice   FCC Class B Radio Frequency Interference Statement  WARNING:...

3.  The manufacturer is not responsible for any radio or TV interference caused by unauthorized modific ation to this equipment. It is theresponsibilities of 
the user to correct such interference. 
WEEE Declaration   Disposal of Waste Equipment by Users in Private Hou sehold in the European Union.   
 This symbol on the product or on its packaging indi cates that this product must not be disposed of with your other household waste.Instead, it is your 
responsibility to dispose of your waste equipment b...

PRECAUTIONS 
· 
Do not use the monitor near water, e.g. near a bath tub, washbowl, kitchen sink, laundry tub, swimming  pool or in a wet basement. 
· 
Do not place the monitor on an unstable cart, stand , or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Us e 
only a cart or stand recommended by the manufacture r or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit 
approved by the manufacturer and follow the kit ins...

Please setup or remove the base following below steps.   
 
Adjusting Viewing Angle  
· 
For optimal viewing it is recommended to look at th e full face of the monitor, then adjust the monitors angle to your own preference. 
· 
Hold the stand so you do not topple the monitor whe n you change the monitors angle. 
· 
You are able to adjust the monitors angle from -5° to 20°. 
 
   

  NOTE: 
Do not touch the LCD screen when you change the ang le. It may cause damage or break the LCD screen.   
    
Attaching the Cables Cable Connections On Back of Monitor and Computer  
 
1. Power
 
2. Audio
 
3. DVI
 
4. Analog
 
  

Turn off your computer before performing the procedure below. 
1.  Connect the power cable to the AC port on the back of the monitor. 
2.  Connect one end of the 15-pin D-Sub cable to the  back of the monitor and connect the other end to the computers D-Sub port. 
3.  Turn on your monitor and computer. 
If your monitor displays an image, installation is  complete. If it does not display an image, see
 Troubleshooting
. 
Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm   
 
 
  

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before t his procedure. Follow these 
steps: 
1.  Remove the base.  
2.  Follow the manufacturers instructions to assemb le the wall mounting arm. 
3.  Place the wall mounting arm onto the back of the  monitor. Line up the holes of the arm with the holes in the back of the monitor. 
4.  Insert the 4 screws into the holes and tighten. 
5.  Reconnect the cables.   Refer to the users manua l that came with the...

 
1.Souce  
2. Auto Config 
3. Volume / - 
4. Volume / + 
5. Menu / Enter 
6. Power Button & Indicator 
OSD Settings 
·  
Press the MENU-button to activate the OSD window. 
· 
Press+ or - to navigate through the functions. Once  the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has 
a sub-menu, press or again to navigate through the  sub-menu functions.Once the desired function is hig hlighted, press MENU-button to activate it. 
· 
Press+ or - to change the...

· 
Eco Mode hot key : Press the Eco key continuously t o select the Eco mode of brightness when there is no OSD ( Eco mode hot key may not be 
available in all models).   
·  
Volume adjustment hot key : Press Volume / - or Vol ume /+ to adjust volume when there is no OSD ( Only  for the models with speakers)   
· 
Press Exit key continually for 7 sec. to turn on or  off DDC-CI. 
 
DCB Adjustment  
 
What is DCB?   
  
Dynamic Color Boost (DCB) is an advanced color adju stment technology. Through...