Antennacraft Antenna HDMS9100 manual

WARNING: INSTALLATION OF 
THIS PRODUCT NEAR POWERLINES
IS DANGEROUS. FOR YOUR SAFETY, 
FOLLOW THE INSTALLATION 
DIRECTIONS.
Before Installation  Note:  to CATV SYSTEM INSTALLER—Article 820-40 of the NEC specified that the cable ground shall be connected to the grounding system of the building “as close to the point of cable entry as practical”.
Note:  Do not plug your Mini-State power supply into an AC outlet or DC power source until all electrical and antenna connections have been made. Doing so may...

15. LIGHTNING—For  added  protection  for  this  product  during 
lightning storm or when it is left unattended and unused for long 
periods  of  time,  unplug  it  from  the  wall  outlet  and  disconnect 
the antenna or cable system. This will prevent damage to the 
product due to lightning and power-line surges.
16. 
OBJECTS AND LIQUID ENTRY—Never push objects or any 
kind  into  this  product  through  openings  are  they  may  touch 
dangerous  voltage  points  or  shortout  parts  that  could...

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO 
NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED
IN ARTICLE 810-”RADIO AND TELEVISION EQUIPMENT”
aUse No. 10 AWG (5.3 mm2) copper, No. 8 AWG (8.4 mm2) aluminum, No. 17 AWG (1.0 mm2) copperclad steel or bronze wire, or larger, as a ground wire.bSecure antenna lead-in and ground wires to house with stand-off insula-tors spaced from 4-6 feet (1.22-1.83 m) apart.
cMount  antenna  discharge  unit  as  close  as  possible  to  where  lead-in enters house.dUsejumper...

Boat  or  RV—The  optional  RV/boat  mount  brackets  will  let 
you  install  the  HDMS9100  antenna  on  your  RV  or  boat.  It  is 
recommended that several locations be tried to find the one 
that provides optimum performance before you permanently 
install the antenna.
Mount the antenna as high as practical and as far away from 
metal objects as possible. If the interior areas of the vehicle 
or  boat  are  substantially  enclosed  or  surrounded  by  metal 
surfaces, an exterior mounting location...

5
HDMS9100 Receiver Cable ConnectionsInstalling the Battery
Coaxial Cable to TV
Cable to Antenna
TVANT
Terminals1–Yellow or Red  2–Black    3–White or Blue
3-Wire Rotator Cable
TV
123D C12V
ANTENNA CONTROL
for 12 VDC power adapteror DC power cord
Note:  Do  not  plug  your  antenna’s  power  supply  into  an 
AC outlet or DC power source until all receiver and 
antenna  connections  have  been  made.  Doing  so 
may short out the receiver’s transformer and void 
your warranty. 
AC POWER—Insert the 12...

There may be cases that the receiver is triggered by another 
transmitter  in  your  neighborhood,  or  a  nearby  RV  with  the 
same antenna. 
If  you  find  the  receiver  is  receiving  and  reacting  to  some 
commands  which  have  not  been  sent  from  your  remote 
control,  you  can  change  the  Transmitter/Receiver  ID  code 
pair by following the below procedures:
1.  Unplug the power cord from the receiver.
2.   Hold down the ‘UP’ and ‘DOWN’ keys together and power 
up the receiver until...

Do not service this product yourself, as opening or removing 
covers may expose you to dangerous voltage or other hazards. 
Refer all servicing to qualified service personnel.
Available  Parts: 
50009100RX Receiver
50009100TX RF Transmitter
30' or 60' Combination Cable
RV/Boat Mounts (1 pair)
UAM9000 Universal Antenna Mount
MINI-STATE® HDView360® HDMS9100 ANTENNA LIMITED WARRANTY
We warrant that if anything goes wrong with your ANTENNACRAFT® HDView360® Mini-State® Antenna within 90 days of...

8
1. LIRE LES DIRECTIVES – Lisez les directives de sécurité et d’utilisation avant 
d’utiliser l’appareil.
2. 
CONSERVER  LES  DIRECTIVES  –  Conservez  les  directives  de  sécurité  et 
d’utilisation pour référence ultérieure.
3. 
RESPECTER LES MISES EN GARDE – Respectez toutes les mises en garde 
sur l’appareil et dans la documentation.
4. 
SUIVRE LES DIRECTIVES – Suivez toutes les directives d’utilisation et de 
fonctionnement.
5. 
EAU  ET  HUMIDITÉ  –  N’utilisez  pas  l’appareil  près  de  l’eau...

1. Desserrer les deux vis sur la couverture de conseil délimi-
tante  sur  le  fond  de  l’antenne.  Ceci  exposera  une  prise 
coaxiale enfilée et trois terminaux de vis-tape spéciaux.
2.  Visser le connecteur d’avance-dans du câble coaxial fourni 
sur le terminal enfilé.
  Prudence:  Être  sûr  le  conducteur  de  centre  du  câble  est 
dans le trou du connecteur de F avant de resserrer.
3.  Vos câbles peuvent avoir soit des fils de couleurs JAUNES/
NOIR/BLANC ou ROUGE/NOIR/BLEU pour brancher votre...

Note: Ne pas brancher la source d’alimentation CA ou CC avant 
que tous les branchements entre votre récepteur et l’antenne 
soient  finalisés.  Ne  pas  suivre  les  étapes  suggérés,  peuvent 
endommager  le  transformateur  du  récepteur  et  annuler  la 
garantie.  
Pouvoir CA—Boucher le DC de l’adaptateur de courant alter-
natif  CC  12V  connecte  au  12V  cric  de  DC  sur  le  HDMS9100 
alimentation.
Pouvoir CC—Boucher le 12v cordon d’alimentation de dc dans 
le cric de dc sur le HDMS9100...