Home
>
Anetsberger Brothers
>
Fryer
>
Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard Parts List User Manual
Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard Parts List User Manual
Here you can view all the pages of manual Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard Parts List User Manual. The Anetsberger Brothers manuals for Fryer are available online for free. You can easily download all the documents as PDF.
Page 1
L22-371 Rev 0 2/13 IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment: Model #: __________________________ Serial #: __________________________ Date Purchased: ___________________ Service & Parts Manual Covering the 14GS Series ENGLISH
Page 2
L22-371 Rev 0 2/13 TO THE PURCHASER Post, in a prominent location, the instructions to be followed in the event that an operator smells gas. Obtain this information from your local gas supplier. WARNING There is an open flame inside this appliance. The unit may get hot enough to set nearby materials on fire. Keep the area around the appliance free from combustibles. WARNING DO NOT supply the appliance with a gas that is not indicated on the data plate. If you need to...
Page 3
L22-371 Rev 0 2/13 TABLE OF CONTENTS 1 Leg Installation and Leveling -------------------------------------------------------------------------------------------------------------- 4 1.1 Installation Clearances ------------------------------------------------------------------------------------------------------------------- 4 1.2 Gas Connection --------------------------------------------------------------------------------------------------------------------------- 4 1.3 Gas Connection...
Page 4
4 L22-371 Rev 0 2/13 1 Leg Installation and Leveling This appliance must be installed with legs; it cannot be curb mounted. Curb mounting will seriously inhibit this appliances ability to effect proper combustion. WARNING This appliance must be installed with the legs provided by the manufacturer. WARNING Do not install legs or perform leveling procedure when unit is in operation or full of cooking medium. Serious injury could result. Required tools: 7/16 “ wrench and socket and a large...
Page 5
5 L22-371 Rev 0 2/13 1.4 Fuel Supply Line Leak and Pressure Testing The fuel supply system must be tested before the appliance is used. If the fuel line is going to be tested at a pressure greater than ½ PISG (3.45 kPa), insure that that appliance is disconnected from the fuel line. If the fuel line is to be tested at a pressure equal to or less than ½ PSIG (3.45 kPa), the appliance can be connected during the test, but the unit’s gas valve must be shut. Test all gas line connections for...
Page 6
6 L22-371 Rev 0 2/13 2.2 Main Burner System Adjustment For the main burners to operate the gas supply valve must be open and the thermostat must be turned on. For models with electric controls, the main power switch must be on. The main burners receive gas from the main gas supply through the thermostatically controlled valve. When the thermostat is turned up to a setting higher than the temperature of the oil in the tank, the gas control valve opens. The main burner pressure must be adjusted...
Page 7
7 L22-371 Rev 0 2/13 CAUTION If the burners do not shut off at the LOWEST thermostat setting, the thermostat may be defective. Contact your local service company. 2.4 Thermostat Calibration For Gas Operated and Electric Thermostats refer to the following procedure. a. Remove the tube screen from the tank and place the tip of a digital thermometer in the shortening/oil approximately one inch above the temperature sensor. b. Light the pilot as described in this manual, set the thermostat...
Page 8
14GS-CS Series 8 L22-371 Rev 0 2/13 3 Trouble Shooting Refer to this section to correct common problems that may be encountered during the course of normal operation. If applicable, a schematic is provided behind the panel containing the electrical components. NO YES YES Appliance does not work. Will the pilot light? NO Is the gas supply valve o pen? NO Open the gas valve...
Page 9
14GS-CS Series 9 L22-371 Rev 0 2/13 3.1 Testing the Thermocouple: You will need a multimeter that can measure millivolts. Make sure that after holding a flame to the thermocouple it produces 30 mv. You can test for this by heating the thermocouple for about a minute and then place one lead on the copper casing of the thermocouple and the other lead on one of terminals of the hi limit wire connection. This is the easiest way to check the thermocouple but you are also going on the faith that the...