Analog Devices ICE100B Emulator Users Guide Rev 11

ICE-100B Emulator User’s Guide xi Preface
provides access to books, application notes, data sheets, code examples, 
and more.
Visit 
myAnalog to sign up. If you are a registered user, just log on. Your 
user name is your e-mail address.
EngineerZone
EngineerZone is a technical support forum from Analog Devices. It allows 
you direct access to ADI technical support engineers. You can search 
FAQs and technical information to get quick answers to your embedded 
processing and DSP design questions.
Use...

Notation Conventions
xii ICE-100B Emulator User’s Guide
[this,…]Optional item lists in syntax descriptions appear within brackets delim-
ited by commas and terminated with an ellipsis; read the example as an 
optional comma-separated list of 
this.
.
SECTIONCommands, directives, keywords, and feature names are in text with 
letter gothic font.
filenameNon-keyword placeholders appear in text with italic style format.
Note: For correct operation, ...
A Note provides supplementary information on a related...

ICE-100B Emulator User’s Guide 1-1 
1 GETTING STARTED
This chapter provides the information needed to begin using Analog 
Devices ICE-100B emulators. 
Analog Devices emulators are not intended to be used in a 
production environment. 
This chapter includes the following sections.
“Contents of Emulator Package” on page 1-2
Provides a list of components shipped with the emulator.
“PC Configuration” on page 1-2
Describes the minimal PC requirements.
“ICE-100B Installation Tasks” on page 1-2
Provides a...

Contents of Emulator Package
1-2 ICE-100B Emulator User’s Guide
Contents of Emulator Package
The ICE-100B emulator package contains the following items.
 ICE-100B emulator
 2-meter USB standard-A to mini-B cable 
PC Configuration
For correct operation of the ICE-100B emulator, your computer must 
have the minimal configuration:
 Windows XP SP2 or later, Windows Vista, or Windows 7
 CrossCore Embedded Studio 1.0.0 or VisualDSP++ 5.0 Update 7 
(or higher)
ICE-100B Installation Tasks
Perform the following...

ICE-100B Emulator User’s Guide 1-3 Getting Started
Installing the Emulator Software
Install CCES 1.0.0 or VisualDSP++ 5.0 Update 7 (or higher) on your 
computer. The software installation includes the USB driver needed for 
the ICE-100B emulator hardware. 
Refer to the Installation Quick Reference Card for details.
Note: If you connect to the ICE before installing the software, the Win-
dows driver wizard may not find the emulator driver.
Configuring and Connecting the JTAG Interface is next. 

ICE-100B Installation Tasks
1-4 ICE-100B Emulator User’s Guide
Configuring and Connecting the JTAG Interface
1. Select the operating voltage of the target processor’s JTAG inter-
face. The ICE-100B emulator ships with a jumper (
JP1) on 
positions 1 and 3, and 2 and 4 (default). Refer to Table 1-1 and 
Figure 1-2. 
2. Ensure that 
JP2 does not have a jumper across the pins when using 
VisualDSP++ or CrossCore Embedded Studio. Refer to Table 1-2. 
There may be a jumper hanging off one pin; this does not...

ICE-100B Emulator User’s Guide 1-5 Getting Started
3. Connect one side of the provided USB cable to the ICE-100B 
emulator and another side to a USB port of your computer.
Verifying Driver Installation and Attaching to an Emulation Target is 
next.
Before connecting to a target, see the power-up/down procedures 
in “Applying Power to the Emulator” on page 1-7. 

ICE-100B Installation Tasks
1-6 ICE-100B Emulator User’s Guide
Verifying Driver Installation and Attaching to an 
Emulation Target
Before using the ICE-100B emulator, verify that the driver software is 
installed properly. 
1. Open the Windows Device Manager and verify that the ICE-100B 
emulator appears under ADI Development Tools, as shown in 
Figure 1-2.
2. Connect the 14-pin header (
J1) of the ICE-100B emulator to the 
target board via the JTAG interface as follows.  Figure 1-2. Verifying Driver...

ICE-100B Emulator User’s Guide 1-7 Getting Started
The 14-pin connector is keyed at pin 3 on the emulator connector 
to ensure that the signals mate correctly with the 14-pin target 
emulation header. The target board should also have pin 3 of the 
JTAG interface connector cut. Refer to Figure 1-3 for 
J1 pinout 
information.
Applying Power to the Emulator is next.
Applying Power to the Emulator
To power up the ICE-100B emulator:
1. Apply power to the target board.
2. If not already, connect the USB port...

Configurator Software
1-8 ICE-100B Emulator User’s Guide3. If the emulator is not connected to the target, connect the devices 
as described in “Verifying Driver Installation and Attaching to an 
Emulation Target”.
4. Invoke CrossCore Embedded Studio or VisualDSP++.
To power down the ICE-100B emulator:
1. Shut down (exit) CrossCore Embedded Studio or VisualDSP++.
2. Disconnect the USB cable between the emulator and the PC.
3. Power down the target board.
The PWR LED (power LED) lights green when power...